Question about Harley Davidson Motorcycles

1 Answer

Need to change rear injector on my 05 ultra classic. Code reads p0264. How do I get the throttle body off or get to the injector

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 40,650 Answers

Hi Bryan, this is not easy for the inexperienced, you might want to take it to a qualified tech. Basicly you have to remove air cleaner and backing plale, raise fuel tank in the back or as necessary to gain acess to throttle body and intake manifold, then disconnect all cables and wire connections and fuel lines. The injectors are located in the intake manifold held in place by the fuel rail. Your going to need new o-rings, clamps, and seals in addition to the new injector. Good luck.

Posted on Mar 31, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jagjeffery
  • 318 Answers

SOURCE: throttle body injectors not fiering but there is fuel pressure

the injectors are fired thru the engine cotrol module but it gets its signal to fire from the pick-up located inside the distributor if you are loosing injector pulse only the ignition module is bad if you are also loosing spark when you loose injector pulse your pick up is causing the problem if you replace the pick-up i recomend you change the ignition module when doing so because they work together and you have to remove the distributor to change the pick-up

Posted on May 31, 2009

johnjohn2
  • 5763 Answers

SOURCE: 05 Impala missfire code 301 have changed

check intake for vaccum leaks,the gasket also and egr valve, thats alot of parts to have replaced without diagnosing first, if there are no fuel leaks and you said all injectors were replaced then you have a defective fuel pump, also these engines had misfire problem because of dirty injector but you replaced them so count that out. good luck.

Posted on Nov 02, 2009

  • 78 Answers

SOURCE: 1993 geo tracker fuel injector

ecm does control but is also based on input from the Throttle position senser. unplug the TPS and try again. Also make sure the ECM and engine grounds are good

Posted on Feb 21, 2010

johnjnail
  • 1702 Answers

SOURCE: V6 T3000 need torque specs

3.0L and 3.5L V6

Torque Specifications

air intake plenum 11-14 ft lbs.

camshaft bearing cap 14-15 ft lbs.

connecting rod nut 37-38 ft lbs.

camshaft sprocket bolt 66-67 ft lbs.

crankshaft pulley bolt 108-116 ft lbs.

cylinder head bolts 65-72 ft lbs. ( 3.0L) 76-83 ft lbs. (3.5L)

drive plate ( flywheel ) 53-55 ft lbs.

exhust manifold 11-16 ft lbs.

intake manifold 11-15 ft lbs.

main bearing cap 55-61 ft lbs.

rocker shaft 14-15 ft lbs.

valve cover 27-35 in. lbs.

throttle body bolt 84-108 in. lbs.

Posted on May 20, 2011

  • 1 Answer

SOURCE: 1990 chevy blazer 350 ci throttle body fuel

truck is missing and it back fires, started after i washed engine, replaced distributercap,plugs,wires,coil,ignition model,throttel body sencer,map sencer, its still missing. brake warning light flashes 7 times and stays on on the 7th flash. please heip

Posted on Jun 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

MY deville 05 shows Code 171/174 Bank too Lean.How do u repair this problem


could be HO2S sensors not operational
low fuel pressure
problem injectors

Jan 12, 2017 | 2005 Cadillac Deville

1 Answer

Why is there no throttle response and the engine light is on on my 2010 HD FLHTCU 96 ci ?


You've got to twist the grip HAHA ! Seriously, you can do a test by yourself, press the trip button on the speedo, with the ignition off. One second later (keeping the button pressed) turn the ignition on and you-ll see a self test on the speedo. After the needle pegs and all leds come on, you'll see in the counter area a type of code. Using the trip button again you can read the ecm and tsm modules errors. Just press and hold the trip button as you go along. In one of the fields an error should come on like "P1005" or similar. You can look it up on the net. There is also a TSB out on the throttle TT-418 there were issues with the terminal connections at the throttle body.

Jun 24, 2014 | 2005 Harley Davidson FLHTCUI Electra Glide...

2 Answers

Fault code po262. have changed injectors twice. checked wiring. looks ok could it be ecm


P0262 = Front Injector High EFI

One thing you can try is to swap the injectors front to rear, and see if now you get a P0264 error code.
If so, that tells me that the injector itself is the problem.

Sometimes one of the injector wires can break inside of the insulation and the wire will look fine.
You might try wiggling the injector wire while the engine is running and see if you get a code.

Apr 26, 2014 | Harley Davidson FLSTC Heritage Softail...

1 Answer

Trottle cuts out on 09 ultra classic hd


There's probably a sensor in your throttle housing that regulates the amount of fuel that goes through the throttle body to the engine. The sensor could be located on the throttle or you may have a bad throttle body. There are computers on both ends. I believe you ought to call the dealer and find out

Mar 31, 2013 | 2009 Harley Davidson FLHTCU Ultra Classic...

1 Answer

Harley p2176 solution


DTC P2176 = Throttle Acuation Control: closed position not learned (2008-2009 models)


Remove air cleaner and check Throttle Body inlet for debris or mechanical interference restricting movement of throttle plate.


If none is present, replace Induction Module.


If present, clear obstruction, clear code from memory.
Start engine, operate throttle several times.


If code does not come back, system OK.


If code reappears, replace Induction Module.

Feb 15, 2013 | 2008 Harley Davidson FLHTCU Ultra Classic...

1 Answer

My 05 Ultra Classic keeps displaying "tip" on the


it means your bike was tipped over. It should reset after a short while. Unfortunately I know this from experience.

Feb 23, 2011 | 2005 Harley Davidson FLHTCUI Electra Glide...

2 Answers

My 1998 Chevy Blazer crank excessively when I try to start it. It always starts, and runs good when I get it started, but I would really like a smooth start. I have recently changed the fuel filter, spark...


leaky injector/s is flooding motor, mechanically clean or replace. And clean throttle body while you are at it with spray cleaner. Should be almost spotless where large throttle valve opens and closes.

Oct 21, 2010 | 1998 Chevrolet Blazer

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...