Question about 2012 Kymco Super 8 50 2T

Open Question

Will the 14100-keb7-900 reed replace the 14100-keb7-c00, and is this wise with a bbk?

Honestly looking for my options, already suffering from reed failure.

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

9500HR does not come on, where do I start looking for the problem?


I would start by checking the reed switch. Check the gap between the reed switch and the magnet mounted on the back of the flywheel.

LifeFitness 95Xi Crosstrainer Video Reed Switch Replacement Speed Sensor

Oct 09, 2014 | Exercise & Fitness

1 Answer

I have a proform tredmill it will start and run for about 10 sec, beep twice and stop, you can start it again and it will do the same, i have replaced the reed switch already


hi there,
I do suggest ringing Icon Fitness and organizing a tech to come out and fix. The reed switch is rarely the problem with any treadmill.

Dec 15, 2013 | Proform 520 Trainer Folding Treadmill...

1 Answer

Several of the reeds stick, producing no sound until suddenly the reed pops and the note plays (although not always with the correct tone). This problem usually doesn't occur until I play the note...


First and foremost i recommend you take your harmonica to a professional for repair. But the problem can be many things that you can fix with a little patience. FIrst youll need to open up your harmonica and look at the condition of the reeds(the plate with the slits.) If they are rusted or warped they have been poorly maintained as water will rust the metal(saliva.) Sometimes simple sanding solves this problem though it seems thats not your problem. Usually the reed is misaligned due to excessive use and a professional would fix this with an index card sliding it very slowly under each tip of the reed attempting to level out the small piece of metal. Your attempting to realign the reed with the entire board. To see if your fix has worked you can blow into the reed and see if a smooth vibration comes out. Any more complex solutions would honestly show that its time for either a new reed plate or a new harmonica. For future reference make sure to get all saliva out of your harmonica when done playing it and keeping it in its case. Good luck

Sep 12, 2011 | Hohner 280/64 Chromonica 64 Chromatic...

3 Answers

Kx 125 reed valves


The reed valve assembly should hold solvent withot leaking. Remove for test. Disassemble and clean reeds and reed seat. Perfect seal is very important.

Good luck,
Techjoel

May 17, 2009 | 2003 kawasaki KX 125

1 Answer

Air compressor not filling tank


Most compressors with the problem that you are having suffer from leaking valves. As in a gasoline engine, leaking valves will lower efficiency. Valves in a compressor are in the form of reeds that seal against valve plate. Leaking reed valves or gaskets will increase the discharge air temperture. Inspect these parts with a magnifying lense. Look for evidense of wear or leaks. Also look for signs of air leaking from one cylinder to the other thru gaskets. Replace valve plate as necessary. Simple test, as your compressor is filling, check the intake for strong suction; as it neers the 92 psi mark suction will probably deminish if you have leaking valves. If suction remains strong at 92psi then you have a leak at the discharge side. Check with soapy water on all parts. Good luck

Jan 19, 2009 | Air Tools & Compressors

1 Answer

1989 Mustang GT Keeps dying


Make sure the inside of your throttle body doesn't have a gunk build up. If so, clean in out with some carb. cleaner really well. If the crack is plugged up in the throttle body, air cannot get into the engine at idle in which the car will die. Are you running an aftermarket cam? If you are, drill a 5/32 hole in the center of the lower half of the throttle plate in the throttle body. This helps a great deal as well.

Jul 13, 2008 | 1989 Ford Mustang

1 Answer

Brivis Ducted Heating system. No display on Programmable controller inside hoiuse. Electronic Control (Model 14100) located on Heater (outside house)displays "Searching". Have turned off...


Hi,
I have an identical issue with my Brivis.
Did you get a solution?
Mine can be running, then goes blank and says searching. it will eventually come back.
Just wondering if you had to replace the 14100?

Cheers
James

Jun 10, 2008 | Heating & Cooling

3 Answers

Refill light is on, but the water tank is full


In the manual it says that you should clean the heating element. Unplug the machine, lift off the water tank, pull the lever under the tank and lift off the power unit side. If there is too much build up on the element from mineral deposits, the refill light may remain on.
Unfortunately, I have cleaned mine, soaked it in vinegar, made it look nice and new...and it still doesn't work. I am really annoyed as I have not had this humidifier long and have taken really good care of it. I do not want to throw it out. I am going to call customer support and find out if there are any other solutions. (I got a new one for Christmas and do not want to open it until I am sure that it is not fixable!)

Dec 06, 2006 | Honeywell Warm Mist HWM-2030 Humidifier

Not finding what you are looking for?
2012 Kymco Super 8 50 2T Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...