Question about Motorcycles

1 Answer

How to replace switch

I do not know how to get to the switch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 742 Answers

What switch are you referring too?

Posted on Dec 09, 2014


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace ignition switch on2003 jeep


More details: what exactly you're replacing, just switch or switch+full harness?

Jun 11, 2015 | Jeep Cars & Trucks

1 Answer

How do I replace the 4-wire fans speed control in the Heritage 5ALW52PB3P with a 3-wire speed control?


You have to replace the switch. You cannot open & fix. First, write down which color wire goes into which slot on the switch. Each slot should be marked, usually L,1,2 & 3. DO NOT CUT WIRES. I don't know this fan so you'll have to get a switch where you bought the fan. Otherwise, I need to know how many wires on your capacitor & which slot on the switch they go into. Remember, just because a switch looks the same on the outside doesn't mean it's the same on the inside. fanman9952@aol.com

Sep 15, 2014 | Dryers

1 Answer

How do you know if it is the switch or the clutch when the blades are not engaging?


if no voltage at pto then go to switch if no voltage there check fuse if power there replace switch if voltage at at pto replace clutch switch cost 60.00 pto 200.00

Sep 01, 2014 | Garden

1 Answer

My headlight just stop working i don't know why is there a relay switch some where to replace


check the lamps to see if they are good then start with the fuses..then to the switch itself..repost findings

Feb 09, 2013 | Cars & Trucks

1 Answer

I need to know how to replace my turn signal switch on my steering wheel my windshield washer turner broke off so either I need to know how to fix the windshield washer switch or just replace the whole...


The turn signal switch or in Ford terms "multi-function" switch is easy to replace if you are mechanically inclined. Lower the steering column "tilt" adjustment for easier access. Remove the lower panel (below the steering column). Remove the three screws from the plastic column covers that surround the multi-function switch. Turn the key to the run position, then from the bottom side of the column, use a very small pocket screwdriver, allen wrench or similiar tool to push up on the ignition cylinder release pin. The hole is located just below the cylinder. With the pin pushed, pull out on the key and cylinder. Next seperate the two cover halves and you will see the complete multi-function switch. remove the two attaching screws, remove the electrical connectors and replace the switch. Replace all removed components and you're done! You can purchase the switch at most auto parts stores, ford dealers or ebay. Feel free to ask if more information is needed and I appreciate a vote of four thumbs up. Good luck!

Apr 11, 2011 | 1996 Ford Crown Victoria

2 Answers

Which relay switch do i replace for powers windows on 2002 ford wind star van, drivers window and back sides work passengers doesnt work i was told to replace relay I dont know whick one to replace


Doubt it is a relay,all but one window works! Are you just going to buy a new one,without knowing if it is the problem?
Check the pass window switch.
Switch,okey,remove door panel and check out motor

May 25, 2010 | 1998 Ford Windstar

2 Answers

Need to replace lid switch


Unplug and remove back panel and on left side while facing back panel left top corner. It appears in print having two sheet metal screws coming through top to hold the switch in place. Looks a little tight but I don't think you will have a big problem replacing.
If you have any problems let me know, Thanks Sea Breeze
c523934.gif

May 18, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

MM850 MOWER


can't just replace the switch with on-off.original switch has interlocking with brake, once u pull the trigger the brake circuit will open & close when triggger is release. it is also parts of safety.must common problem is inside the switch terminal eventually the contact will burnt.

Jul 28, 2008 | Black & Decker 19" Electric Lawnhog...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...