Question about BMW Motorcycles

1 Answer

What is the intake and exhaust valve adjustment for a !992 Bmw R100RT mono

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 34 Answers

Cold engine set valve clearance at:
0.10 mm intake or about .003" inch.
0.20 mm exhaust or about .007" inch.
---

Posted on Dec 07, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust valves on Toyota 1991 23re engine


Very carefully my friend. Kidding. Ok, remove the valve cover and anything in your way of removing it. By hand, with a socket and ratchet, on the crankshaft bolt head, turn the engine over to get #1 piston to top dead center on compression stroke. You'll need to find out what the valve lash should be in order to adjust properly, I run the 22R engines and only have specs for that, and have a feeler gage to place between the valve head and rocker arm. Check the gap on the intake valve for it is in position to adjust now because the cam lobe is at the farthest away from the valve. If it needs adjusted closer, turn the nut loose and screw the center in to tighten and out to give more gap, then tighten the jam nut after adjusted. Now turn the crank to bring #3 to top dead center and adjust that intake. Once done go back to #1 exhaust and adjust it. You'll know when the #3 is TDC when the rocker is loose on intake valve along with #1 exhaust. Now bring #4 piston up to TDC and adjust intake valve. Like I said, you'll know when it's @TDC when that rocker is loose, but with the spark plugs out you can stick a screwdriver in the plug hole to be sure it's up. Firing order on 4 cylinders is 1-3-4-2 so do your adjustment in that order for each intake valve and go back to the last one adjusted and do the exhaust valve.

Dec 01, 2014 | Toyota Cars & Trucks

1 Answer

Adjusting shocks


Hi, Anonymous I am sorry you can't find the first and best tool you ever bought for your BMW but despair not for a mere $0 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
Source for rear shocks for 1983 R100RT Vintage BMW Motorcycle Owners
R100 twinshock rear shock upgrade
Free BMW Motorcycle Service Manuals for download
BMW Motorcycle Parts Fiche OEM BMW Motorcycle Parts online 1970 present BMW
http://www.bmw-motorrad.com/us/en/index.html?content=http://www.bmw-motorrad.com/us/en/services/manuals/manuals_main.html¬rack=1

Apr 21, 2014 | 1983 BMW R 100 RT

1 Answer

Adjustment clearance valve rocker tappet


Pulsar 135 original tappet clearances
INTAKE VALVE 0.05 mm
EXHAUST Valve 0.10 mm
Get this valve adjustment done by the experienced mechanic with the help of Feeler Gauge

Aug 28, 2013 | 2010 Bajaj Pulsar 135 DTSi

2 Answers

Valve clearance 4g13


make the engine runs for about 30minutes before adjusting the valves,
valve clearances:
intake valve = 0.20mm(0.008 in)
exhaust valve = 0.25mm(0.010 in)
for reference only when the engine is cold,
valve clearances:
intake valve = 0.25mm(0.010 in)
exhaust valve = 0.30mm(0.012 in)
engine specs: mitsubishi 4g13 1.3L (if you have same engine)

Feb 29, 2012 | Mitsubishi Cars & Trucks

1 Answer

What are the settings on intake and exhaust valves on a 1990 BMW 535i


most vehicles can be set to 12th inlet and 14 exhaust ,except some 70s engines of the high lift cam type GT engines ,i thought this engine was hydraulic tappets but i cannot say as i havent worked on every engine or made over the last 40 yrs but if they are adjustable then these are the settings i would set it up too

Sep 25, 2011 | Cars & Trucks

1 Answer

I have a 2010 MTD Yard machine 21 inch snow thrower {123cc} and it broke a valve tappet bolt.I need to no were to set the intake and egzaust valves clearance.Thanks!


I can give you Briggs and Stratton figures for valve clearances of an engine this size. You may have to experiment a little till it runs right. ...you can adjust the intake valve (when it is closed) while the exhaust is open and adjust the exhaust valve (when it is closed) while the intake is open if you can tell...or ya can adjust them when the piston is at TDC on compression stroke (both valves closed). Intake: .004"-.006" Exhaust .004"-.006" (Vertical crankshaft)....for horizontal crank .004"-.006" Intake.....Exhaust is .006"-.011" Hope this helps . Here is a briggs engine specs chart..can';t find the Chinese engine listed anywhere http://www.briggsandstratton.com/engines/support/frequently-asked-questions/~/media/71BB9DA0BD4D4C19A0DA611923A0B80A.ashx

Jan 21, 2011 | Garden

2 Answers

Procedure of tappet adjustment


make sure engine is warmed up. Put cylinder one at top dead center,remove the valve cover,loosen all adjustment lock nuts,adust intake and exhaust valves on cyl #1 and intake valve on #2 and exhaust valve on #3. now rotate crankshaft 360 degrees clockwise, now adjust intake valves on cyl#3 and cyl #4 and exhaust valves on cyl #2 and cyl #4.now tighten lock nuts and install valve cover. specs are intake valves 25mm clearance and exhaust 28mm clearance, use a feeler gauge,heres a picture to show you where to check clearance.7675a52.gif

Mar 14, 2010 | 1986 Suzuki Samurai

1 Answer

How do i adjust the valves in a ford 1997tarus with a 3.0 ohv


Valve Stem to Guide Clearance · Intake
0.026-0.071 mm (0.001-0.0028 in) · Exhaust
0.038-0.083 mm (0.0015-0.0033 in) Valve Clearance
  1. With No. 1 piston (6108) on top dead center (TDC) at the end of compression stroke (Position No. 1 in the illustration), check the following valves:
    Position 1
    No. 1 exhaust valve (6505) No. 1 intake valve (6507).
    No. 3 exhaust valve No. 2 intake valve.
    No. 6 exhaust valve No. 4 intake valve.
  1. Rotate crankshaft (6303) 360 degrees to position No. 2 and check the following valves:
    Position 2
    No. 2 exhaust valve No. 3 intake valve.
    No. 4 exhaust valve No. 5 intake valve.
    No. 5 exhaust valve No. 6 intake valve. 4cb038f.gif

Oct 19, 2009 | 1997 Ford Taurus

1 Answer

I need the torque values for the nuts securing the valve covers and for the center stud cap nut for a 1983 BMW R100RT.


Rocker cover cap nuts are torque to 22 / 26 Nn and the 6 mm threaded valve cover nuts should be 10 - 20 Nm
Ride Safe
Bike-Doc

Please mark this as useful (if it has been!!)

Aug 02, 2009 | 1983 BMW R 100 RT

1 Answer

Valves making noise BMW 635


the 0.3mm means use thicker gasket if your heads been shaved.valve clearance is 0.012 for intake 0.012 for exhaust valves.what type of oil you using.if your oil is too thick it make valve noise.if adjusting valves dont help your lifters probably worn.

May 20, 2009 | 1987 BMW 6 Series

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

phil cuzins
phil cuzins

Level 2 Expert

79 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...