Question about Moto Motorcycles

1 Answer

How do I replace a tail light on a 250 cf moto fashion scooter, the right rear light

I just need to know how to do it, I broke it and can't see any screws so how does it stay in there

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Moto Master
  • 3,506 Answers

You need to post the year also but if there are no screws that you can see it could be that you need to twist the lens to remove it or more likely it is a push in lens and you would need to grasp it well enough to be able to pull it out and off or possibly VERY carefully get a knife edge or similar between the lens and the light housing and pop it off. If you have the lens off and you are referring to the bulb you will need to twist it a little to remove it. Wear some gloves in case it is rusted or corroded in place and the glass breaks when you twist it, normally to the right as you face it.

Posted on Dec 11, 2014

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MakisRC51
  • 408 Answers

SOURCE: wife learning, dropped 2008cbr125, tweaked signal

Some of the wires are stripped and touches the frame (negative).Start checking harness around the damaged from the drop area.

Posted on Jun 09, 2009

czaa
  • 4536 Answers

SOURCE: I have a 2004 vento

the voltage regulator is probly failin--get it tested along with alternator etc--also inspec wire harness--buy a repaair book by clymer or haynes

Posted on Mar 15, 2011

kel1guy2002
  • 3740 Answers

SOURCE: hi. Need part number for

Hi and wlecome to FixYa, I am Kelly
Part number is 1157 and is available at any automotive light bulb source. This is the most common light bulb used for motorcycles and automobiles that is a TAIL and BRAKE light bulb.
http://www.hyosungsource.com/index.php?main_page=product_info&products_id=609

Thanks for choosing FixYa,
Kelly

Posted on Jul 17, 2011

  • 2 Answers

SOURCE: cf moto 250 revs but won't move

Broken belt or worse, possibly, mine broke a transmission shaft.

Posted on Jan 17, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a white superlock 534- I recently broke a needle and now I cannot load two needles. After unscrewing the screw- I try to load two needles and only the right will stay in--left falling out. If I load...


I have a White Superlock 534,the needle broke and I tried to change the needle and lost the screw,it is so tiny I cant find it,is their any way I can buy the same tiny screw.I like to have 2 needles.

May 29, 2011 | White Sewing Superlock 1934D Mechanical...

1 Answer

One of the baffles broke off. I need to know how


Take the top of of the machine and rotate it until the baffle is at the top.  They usually have clips that hold the lid down, or screws under the head.  If the head is hinged and flips over the back the screws are under the head.  If not fine the clips, get a ling flathead and push it into the clips while prying up.  There are also two screws under the lint trap if it is on top.

Dec 04, 2009 | Dryers

1 Answer

When changing my alternator i broke the screw that adjust the alternator the screw broke in the lil block i tried to get it from a junk yard i couldnt find it do u know where i could get it online or a...


First, you will need to get the broken off screw piece out of the hole you want to sink a replacement screw into. You should be able to use an easy-out tool for this, careful not to ruin the female threads. Then go to your local hardware store, preferably with the alternator, and get the screw that you need.

Jul 19, 2009 | 1999 Lexus ES 300

1 Answer

Broke off hazard botton on column hazard lights stay on all the time


get a small self tapping screw ,
screw it into the hole then take a pair of pliers and turn the switch off,or take the colum apart which is a pain if you dont know how!!!!!

Jun 05, 2009 | 1996 GMC Jimmy

1 Answer

Needing advice on finding xtr repair parts


You can use a good old metal screw for this. If the back of the screw hole is open, just get a coarse threaded metal screw that is approximately the fight diameter and use it. Or, if you want to be precise (and far more safe), take the screw you do have to a hardware store, or a fastener supplier, and have them set you up with the correct screw. i do not know where you live, but if you Google map "hardware store" you should be able to find one pretty close by.

Mar 04, 2009 | Shimano Xtr Mountain Bike Dual Control...

2 Answers

Plastic under flush handle stripped.


If the threads are not stripped on the nut or handle it should be fine. IMPORTANT TO KNOW!!! These are left handed threads, Meaning they tighten up the opposite way of a normal nut and bolt. If the threads are bad or damaged, you will have to purchase a new flush handle. They are not expensive at all. $2 - $10 Dollars. But first try screwing the nut on by turning it to the left instead of the right.

Dec 31, 2008 | Pegasus Technologies Two-Piece Round...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Moto Experts

David Payne
David Payne

Level 3 Expert

14161 Answers

adam bikedoc

Level 3 Expert

661 Answers

Ted Maxwell

Level 3 Expert

3519 Answers

Are you a Moto Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...