Question about Yamaha Motorcycles

1 Answer

1994 yamaha timberwolf will not move when i put it in gear i was riding it up a hill started hearing a bunch of clinging noises and now when i i go to put it in first it wont go any where

Nothing besides making sure it is in forward

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You have messed the gears up in your rearend! I have seen on several occasions that the gears on the rear axle were striped! On your rear gear housing there is a screw at the bottom! Remove that screw and gear oil should run out! Let it drain completely! Put ur finger u Der the stream as it is draining and inspect for metal shavings! If there is metal shaving present u have something going on inside there! If the shavings are fine in nature more than likely you have stripped ur axle not that expensive if u diy! But if u can tell there are pretty good size shards in it then u busted gears! Expensive!!

Posted on Nov 22, 2014

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

co7196
  • 3433 Answers

SOURCE: Yamaha timberwolf wont start unless push started

You have a loose connection to the ignition system . When cranking make sure it is in neutral. and kill switch is in run position. The only thing dropping would sensibly affect is the fuel system or jarring a switch., but with the suspension you have there really is no jarring. So, I would ck the wiring. something is loose.

Posted on May 29, 2009

finish line
  • 207 Answers

SOURCE: won't start

you have a bad solenoid battery or starter try to ground the starter touch positive to groundwith a rubber ended screw driver if the starter spins you have a bad solenoid

Posted on Jun 23, 2009

  • 1 Answer

SOURCE: yamaha timberwolf starts but when you put it in gear wont move

The reverse lever is stuck push it back forward an your good

Posted on May 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Yamaha Timberwolf 250 will not turn over. Took it to someone they said it was stator. Replaced stator and spark plug still wont turn. There's no noise anywhere.


Hi, Anonymous and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
1994 Yamaha Timberwolf 4x4 Electric Start Problems
no fire 96 timberwolf
http://www.mikekekich.com/92-98%20Timberwolf%202WD%20Service%20Manual.pdf
OEM parts for Yamaha
Yamaha YFB250K Timberwolf Owner Manual

Jan 13, 2017 | Yamaha Motorcycles

1 Answer

1994 Yamaha 250 timberwolf piston ring replacement


YAMAHA TIMBER WOLF 250 ENGINE OVER HALL ANN ...

? 3:08
www.youtube.com/watch?v=0fypjxwZV40
May 16, 2010 - Uploaded by omar arriaga
HERE IS MY NEW PROJEC PAINTING MY 250 TIMBER WOLFIM REPARING ... back break replacement on Yamaha timberwolf 250cc tutorial ...

Sep 12, 2015 | Yamaha Motorcycles

1 Answer

2000, v-star 1100, loud winning when slowing down in gear (5th to 1st), sound will stat after going into 1st gear and moving foward again.


Yamaha Vstar middle shaft engineering defect ' Facebook

https://www.facebook.com/vstardefects?fref=ts
'2002 Yamaha Vstar 1100 with motor with broken middle shaft removed. .... VStar for a 1100 and it started making a whining sound when decelerating-- I thought ..

Jul 25, 2015 | 2000 Yamaha V Star 1100 Classic

1 Answer

1994 yamaha timberwolf wont move when i put it into gear


i assume its automatic transmission-so check the trans fluid level & top up if necessary

Nov 21, 2014 | Yamaha Motorcycles

1 Answer

My yamaha timberwolf want go in gear I first started it up and put it in first gear it just jumped in and out of gear could it be my U-Join or my rear end???


Jumping out of gear is a transmission problem, possibly bent shift fork. Does it pop right back out of gear while sitting still? Or does it pop out of gear when you are going forward?

Oct 09, 2014 | Yamaha Motorcycles

1 Answer

Yamaha 250 timberwolf I put in a gear or reverse


Worn transmission shift arms. You will need to remove the transmission and rebuild it.

Aug 12, 2013 | Motorcycles

1 Answer

While riding my 2003 yzf 450 i started hearing a clapping noise coming from the front end (motor) i think but mainly when i go up hill at a slow speed but now when i start out in first i hear it to an


Sounds Like Spark Knock. Go To 93 Octane Gas And Select The Right Gear For Conditions. Do Not Lug The Engine. Lugging Will Damage This Engine Quicker Than Over Revving Will.

Apr 04, 2013 | 2004 Yamaha YZ 450 F

1 Answer

Jetta making grinding noises and not moving, but speedo goes up.


check your half-shafts going from the transaxle to the wheel hubs. I suspect that one of them has broken off.

Aug 05, 2012 | 2002 Volkswagen Jetta TDI

1 Answer

My bike will start but when i try to put it in gear i will go but its like not catching and i can move the bike in gear and all you hear is a click click click and i can't ride it


Hi, Dillionclark5 and the usual suspects are:
1. Clutch controls improperly adjusted.
2. Insufficient clutch spring tension.
3. Friction discs or steel discs are worn or warped
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
TTR 125 clutch problem
2003 ttr 125 clutch adjustment
YAMAHA TT R125 Owner Service Manual
OEM parts for Yamaha
YAMAHA TT R110E Owner Manual

Jul 15, 2012 | Yamaha TT-R 125 L Motorcycles

2 Answers

Yamaha timberwolf starts but when you put it in gear wont move sounds like chain is off but think its shaft driven what wrong with it


DT 360 is not shaft driven . Its chain driven .
Now if its making noises and not going anywhere , the chain may have jump the front sprocket and just knocks on the side cover making strange noises .
check it out and let me know how you go .

Sep 27, 2009 | 1974 Yamaha DT 360

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...