Question about Motorcycles

1 Answer

I have a 150 rr bike and need to know the correct position for the balancing shaft in relation to the cranck shaft

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 157 Answers

There should be marks on the balancer drive and driven gears. The "pork chop" weight on the balancer runs exactly opposite the piston, ie; when piston is up, weight is down.

Posted on Nov 15, 2014

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

sisadsl
  • 1508 Answers

SOURCE: just pulled the shift pedal

the lever sits aprox level, but can be adjusted up or down on the splines to make it comfortable.
There is no real wrong position, as long as the lever doesent touch the frame or casing, up and down gears.

Posted on Aug 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 ford f-150 -misses or cuts out at 40 - 50mph and between 1000 - 2000 rpm


Hey there. I'm not an expert on Ford's, but I had a very similar issue with my Mercedes S550 AMG. I'm hoping my experience will help you. What caused this issue on my car was two things. There was an oil leak running down a wire harness that caused the cam-shaft positioning sensor to mis-read engine data, that caused another sensor (that was trying to correct the problem internally) to go bad. That sensor was the Crank-shaft positioning sensor. This drove me nuts... I replaced the plugs, coil packs, plug wires and a few other smaller things until I gave up. Towed it to the "
Mercedes "Stealer-ship" to find out it was 3 (in my car) relatively inexpensive sensors that needed to be replaced as well as (on my car) a recall to replace the harness with an extension to keep.any fluid from doing this again.

Is your Check Engine Light on? A local auto parts store will code it for you for free in most cases. If you get a code, let me know what it is and we can go from there.

Jun 23, 2016 | 2008 Ford F-150

1 Answer

Can some une please conferm what are the numbers for a well balanced 4g93 cranck shaft?


It is a Billet crankshaft formed for more expensive metals
http://www.callies.com/crankshafts/ultra-billet-crankshafts/

May 21, 2014 | Cars & Trucks

1 Answer

Vabration


IS that vibration related to RPM? If so the harmonic balancer and or the crank shaft might be out of balance. If it is not related to RPM, then you need to check to see if the shafts are all installed correctly and the motor mounts are ok. It could also be the tires flat spotted if they sat a long time.

Jan 22, 2014 | Ford F-150 Cars & Trucks

1 Answer

1987 2.8 v6 Bad vib in engine flywheel not bal cranck.Internal engine


crank shafts are balanced during manufacture. The same crank is used for auto or manual so that statement is a bit off. However if you have not fitted the flywheel correctly and it is hung up on a burr ( dowel ) or is running with a wobble because the bolts have not been tensioned correctly and in the right sequence then that will transfer to the clutch pressure plate as well. Was there positioning dowels in the fly wheel that positioned the pressure plate correctly or did you rely on the bolts alone as that will cause an unbalance . Position a dial indicator on the bell housing with the needle on the fly wheel and turn the flywheel over by hand and watch for run out on the flywheel . There should be virtually none shown . If there is remove the flywheel and clean out the groove and check the crank for imperfections.

Jan 19, 2014 | Cars & Trucks

1 Answer

The front wheel of my yamaha 80 wobbles when I am riding my bike. what is wrong


There can be two issues related to this problem.
The front wheel can be off balance on the bike. This means you will need to balance the wheel using a wheel balancer.
Secondly the wheel bearing could be faulty and result in wobble. You will need to check the front assembly fully, check the suspension and shaft.

Feb 17, 2011 | Yamaha YX 600 Radian Motorcycles

2 Answers

My 97 sunfire has a bad cranck shaft sensor. where is that located? would it also make the car not start?


Yes it would and will make the car not start. Your crank sensor is located behind your harmonic balancer, which is the large pulley that turns all the belts. THe one that is coming off the crank shaft.

Apr 10, 2010 | 1997 Pontiac Sunfire

1 Answer

I want to buy a new bike , may i know abt pulser 135, many were telling its a flap, is it correct


yes... basically the pulsar bike is not a balanced one...it weigh more near the dome, due to which contolling the bike ones u apply front break becomes difficult... so chances of accident are more in pulsar...

If u ask my suggestion, better look around some Yamaha bikes in which u can get better bikes with almost same price and performance...with more stability than pulsar

Apr 06, 2010 | 2007 Bajaj Pulsar 150

1 Answer

What is the function of balancer in this bike.


A balance shaft is used to "counter" the throw of the piston, to smooth out vibration.

Jan 11, 2010 | 2005 Bajaj Pulsar 150

3 Answers

Harmonic balancer wobble will it cause any more


yes besides causing a vibration while driving and possible throwing belts the balancer out of balance can cause problems with the lower end crankshaft such as seal leaks ,bearings and if breaks off or apart can cause damage to engine and body

Nov 24, 2009 | 1990 Buick Century

3 Answers

Balancer pulley turns 1/8 turn before crank


Remove yonder pulley and you will find the bolt holes are elongated. get another from a scrapyard (take the bolts too.) replace and you should be fine.

Apr 07, 2009 | 1994 Buick Regal Gran Sport

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...