Question about Motorcycles

1 Answer

<!-- from fixya rte -->How do i install float on makooney carb - Motorcycles

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Master
  • 1,727 Answers

Lol...

Posted on Nov 09, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Gas pouring out the carb


Flows outside or inside? possible the hose to the carb has a leak or split in it?

Mar 26, 2015 | Garden

1 Answer

How to install float on mikuni carb


remove carb, remove float bowl, remove float pin, install new float needle, reverse to install

Nov 09, 2014 | Mikuni Motorcycles

1 Answer

I have a Sears Eager 1 self propelled mower.. the Carb float was not shutting off the fuel gas was running into the engine and out the carb. I took the Carb apart. the needle and seat looked fine so I...


If there is freedom of movement for the needle, then look towards the float. Does the float have any fuel in it? If so, it will not rise properly to move the needle to shut off flow to the carb which will cause the flooding you are observing. If no fluid in float, you mentioned that you raised the float a little, should have gone the other way. By lowering the float it will seat the needle at a lower level in the bowl. Ensure that the needle seat is properly installed. If this does not solve the problem, purchase a new float.

Note: The model number of the mower is not helpful here. What is required is a model number and brand for the motor.

Jul 08, 2011 | Craftsman Garden

1 Answer

Hi ive a rm 250 and its constontly leaking petrol from the over flow on the carb wen the petrol is turned on its happing wen the bike is running and turned off please help??


The float in carb is stuck open. Remove the float bowl at the bottom of the carb dump out the fuel and trash in the bowl then use spray carb cleaner on the float needle area while gently lifting and releasing the float. Put it back together and try it. If the problem continues, remove the float and shake it. Anything inside the float? A crack in a seam on the float can let fuel/water into the float. This kills the ability of the float to shut off the fuel feed to the carb. Consider installing an in-line fuel filter to prevent future problems.

Mar 17, 2011 | Suzuki RM 250 Motorcycles

1 Answer

Stuck Floates for a mccooney carburetor 1997


you need to remove carb., take off fuel bowl. float should be held in place with small pin, remove pin, float and needle valve. clean needle, needle bore with carb cleaner. inspect needle seat and tip for any dirt/debris. install needle float as assembly, then check float adjustment height

Jun 23, 2010 | Harley Davidson FLSTFI Fat Boy Motorcycles

1 Answer

Carb float on a 1988 hondahurricane


With the float installed turn the carb upside down so the float is pointing up adjust the tab until you see the underside of the float is parrellel to the carberator's metal flat body section. This setting will provide the proper fuel level in the carb providing the proper maintained level of fuel for performance around tight turns as well as idling.

Mar 25, 2010 | 1987 Honda CBR 1000 F

1 Answer

How do I put the float and bowl back on my Troy-Bilt generator. Gas is leaking out of carburator unless gas is cut off. Also where does the spring goes?


The fuel needle sets in a recess in the carb. the retaining clip is attatched to the tab on the float and the needle attaches to the clip carefully install the fuel needle/float assembly into carb inster pin to retain float into carb replace rubber seal on carb. / bowl cover assemble

Dec 19, 2009 | Electrical Supplies

1 Answer

Kawasaki EL250 carburettor


Turn off the gas and remove the float bowl. Remove the fuel line. Remove the float pin and float with needle valve. Do not bend the tang that the float needle sits on. Spray carb cleaner into the seat where the needle valve came from to clear out any trash in the valve casing. Spray the float bowl and interior of the carb. Remount the needle and float back in place and put the float bowl back on. Install an in-line fuel filter. The diagram below shows a 1994 carb Yours will be the same or close to it.

A “very helpful” rating on this answer? Thanks!

6d12579.gif

Jul 03, 2009 | 2001 kawasaki EL 250 Eliminator V

1 Answer

I need to reset the float levels in my carbys to stop the overflow on my 1974 Z1A Kawasaki


You describe a problem with either the float or the float-needle and seat. If the needle is not seating then the gas flows past it. If the float has a pin-hole leak, then it will fill with gas and sink.
On some bikes you can remove the carb bowl without removing the carbs. If so, slide the hinge pin holding the float to one side and remove. The float will drop straight down. Catch the needle since it is now loose. Unscrew the needle seat with a socket.
Clean all metal parts in carburator cleaner...do not get carb cleaner on any rubber part. Shake the float and listen for gas inside or see if it floats in water.
Test the needle seal in the seat by blowing gently thru seat. Needle must seat completly with very little pressure holding the needle in the seat.
Re-assemble with new bowl gasket if damaged. A carb rebuild kit ($35) might be available for 1973 carb and contains all new parts instead of cleaning. Kit might even contain new float and float adjust guide.
Avoid adjusting float level if re-using the old float. If using new float, temporarily install old and measure distance to carb body. Install new and match this measuremnt. Bend tang to adjust.

Good luck,
Techjoel

May 05, 2009 | 1974 kawasaki Z1A

1 Answer

2nd cylinder not getting hot and leaking fuel from it


Assuming the carbs were rebuilt properly, this sounds to me like a carb float being stuck open. Turn off the gas and drain the offending carb. Next, turn the gas back on and sharply tap the float bowl with the plastic handle of a screwdriver as the fuel bowl refills. The goal here is to vibrate the float to free it up. If doing this process a couple of times does not free the float I would remove the carb and look at the float chamber fo any problems such as stuck float, float level not set correctly, and the correct installation of the main jet.
..
Use an air hose to dry out the cylinder then install a new spark plug AFTER you make sure that the cylinder is getting spark. Be sure to balance and sync the carbs when finished.
..
Please rate this solution.

Mar 17, 2009 | 1977 Suzuki GS 750

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...