Question about Motorcycles

1 Answer

I had carb clean now 1 and 4 work but 2and3 is not working

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Motorcycles Master
  • 3,506 Answers

Were the carbs adjusted??

Posted on Nov 09, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do my motorcycle want to stall when I go past 1/4 throttle? I cleaned the tank, carbs, new fuel filter , air filter and plugs


possible fuel pump. same problem happend to a friends bike and in the end it was not enough petrol comming out of tank. he also did all that you did cleaned carb ,tank, ect. in the end he prayed wd40 on carb and jets and around fuel tap and it worked for him hope it works for you.

May 25, 2014 | 2005 Yamaha Vino Classic

1 Answer

Mower won't start


Remove old gas. Remove carb bowl and clean. Ensure float is working, float down gas flow. Float up no gas flow. Use a bread wrap, clean off 1 1/2 in to expose wire. Insert wire in tube from bottom of carb up to behind choke flap. Ensure needle valve moves smoothly when float is moved up & down. Remove plug, should be wet if gas is getting to cylinder. Ensure air filter is clean. Ensure oil has been changed and filled properly. Ensure primer bulb isn't cracked. Pull recoil rope twice half way to prime carb then pull all the way.

May 17, 2014 | Honda Garden

1 Answer

Ignation coil 2and3 no ignite


switch 2 & 3 to 1 & 4 & see if problem follows coil. If so, bad coils.

Apr 21, 2014 | Mitsubishi Lancer Cars & Trucks

1 Answer

1yr old won't start this year


Dirty carb. Remove screw on bottom off carb exposing the carb float. Clean the float bowl. Ensure the float is working by pressing up on the float fuel flow stops, let it fall down, fuel flow. Observe the screw that you removed from the bowl, Look for to see if it has a whole thru it. Clean out the whole if it does. Bread wrapper wire with 1 in plastic cleaned off wire works good. Observe center fuel port, use wire to clean out port going to bottom of carb. Remove pin that holds float and meter needle, use wire to clean out port. Reassemble. Ensure free movement of float. Float up no fuel flow. Float down fuel flow. Use carb cleaner to clean carb inside. Ensure choke opens/closes properly. Always use Stabile in gas.

Jun 11, 2013 | Toro Power Lawn Mower

1 Answer

Husqvarna 181 se wet plug wont start -low is 1/4 turn -high is 1/4 turn- checked diaphgram - checked & cleaned carb


i would remove the muffler and clean the screen inside they build up with carbon and more so when you have carb problems

Aug 12, 2012 | Husqvarna Chain Saw Handle Models 181 281...

1 Answer

MY 97' VALKYRIE SEEMS TO BE DEAD ON ALL 3 RT CYLINDERS, WITH IT IDLING IT RUNS ROUGH. HIGHER RPMS SMOOTHES OUT IS THE LOW IDLE JETS HARD TO CLEAN ? THE DEALER SYS 900.00 I CAN'T HANDLE THAT AMOUNT...


hi had a similar problem with 1 of these i think you will find it is carbs, bit of a tough job to do but not impossible if you are mechanicaly minded, i would however say to save confusion, do 1 carb at a time completely finish and put together each carb before you do the next 1, tip, i found the floats were sticking and required removal for valve cleaning, just work on the cylinders that arnt working leaving the others alone.

Dec 08, 2010 | 2000 Honda Valkyrie Interstate

2 Answers

Atv will not idle without choke


Carb. needs cleaned, its starving for fuel and by choking it you reduce the air flow and increase the fuel.

Rate my answer witht the thumbs..........Thanks

Dec 03, 2010 | Yamaha RD 250 Motorcycles

2 Answers

I have an 81 yamaha 650 maxim that will only idle with the choke on


WELL ITS SOUND LIKE YOU HAVE CLOGED JET IN CARB OR CACUME LEAK AT THE CARB BOOT NEED TO CLEAN CARB IF BOOTS OK

Mar 16, 2010 | 1981 Yamaha XJ 650

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...