Question about Motorcycles

1 Answer

King 2000 whatt gen overreving full speed consrantt

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

It could be that the butterfly is stuck wide open in the neck of the carb so that's it's running at full revs . Try look and if it's stuck free it up .

Posted on Nov 07, 2014

  • john fletcher Nov 07, 2014

    It could be that the butterfly is stuck wide open in the neck of the carb so that's it's running at full revs . Try look and if it's stuck free it up .

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is king craft 2200 generator govonor not working


Are you talking about idle switch or the primary running speed. Had the Gen. been stored for awhile. Check for free movement of linkages to Carburetor.

Aug 21, 2014 | Electrical Supplies

1 Answer

Tecuseth Snow King Engine. Starts fine. When I engage snow blower engine dies.


couple of things come to mind. Safety switch. Engine not running at full speed or snow thrower is locked smooth up

Dec 17, 2013 | Tecumseh 5hp Engine Snow King Mtd Blowers...

1 Answer

My 2000 road king stalls at red lights and stops signs...runs fine at higher rpms


Is the idle speed too low?

Unfortunately, if it is, with fuel injection you'll have to go to a dealership that they can "plug in" their equipment to adjust the idle.

Apr 18, 2013 | 2000 Harley Davidson FLHRCI Road King...

1 Answer

I have a flashing oil light while the engine is running on my 2000 Road king


d01 Speed sensor power output shorted low - Red wire
d02 Speed sensor power output shorted high or open - Red wire

Test your oil pressure sending unit.

May 22, 2012 | 2000 Harley Davidson FLHRCI Road King...

1 Answer

Changing the speed sensor on a 2001 FLHRCI where will I find the connection for the electronic speed sensor harness?


Most of the electronic speed sensors are located on the right rear corner of the transmission. I think this is what you're asking anyway.

Good Luck
Steve

Oct 28, 2010 | 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

2003 HD Road King - starts fine, idle normal. Once it is warm, idles at 2000 rpm. Does not come back down, even after riding for an hour or two. Only idles normal when cold. Help??


If you bike is equipped with a carburetor, the idle stop screw is located at the top of the carb on the right side. Counterclockwise turn slows the idle speed.

If you bike is fuel injected, a dealer or shop will have to set the idle speed electronically.

Good Luck
Steve

Sep 16, 2010 | 2003 Harley Davidson FLHRCI Road King...

1 Answer

Oil change procedure 2000 road king


the oil tank is on the bottom of the transmission in your RK. There are two drain plugs. The plug towards the front left of the pan is the oil drain plug. The other one is for the transmission.

Drain the oil, replace the filter, refill with three quarts of oil and you're ready to go. The dipstick has two marks on it. The upper mark is "FULL HOT", and the lower mark is "FULL COLD". Do not overfill.

Don't forget to service the transmission and the primary at their recommended intervals.

Good Luck
steve

Jul 26, 2010 | 2000 Harley Davidson FLHR-FLHRI Road king

3 Answers

Front end wobble


First thing to do is check front and rear tyre pressures. Next check for un-even wear of front tyre. Then check steering head bearings for correct tightness. Also check for bent front brake disks as one side bent can cause this. Check for worn wheel bearings also. Check engine mount rubbers as these can cause floating on bends if worn of loose. Basically check all chassis related items fully.

Feb 25, 2009 | 2000 Harley Davidson FLHR-FLHRI Road king

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...