Question about Motorcycles

1 Answer

HaveaYamaha250 Grizzly 1998 It kills when I try to shift it in gear

It starts up and idles when chock is on when accelerating it kills have never had a problem I use it for plowing snow have 48 inch blade on it have used it for years

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 196 Answers

If you have to use the choke after the engine has warmed up, it means that the carb is not working properly, maybe a jet is clodded up. Try running some carb cleaner in your gas tank. Also make sure you have good gas in the tank. If that doesn't help, you may need to get the carb rebuilt. When you put the machine in gear, the engine is looking for lots of gas and if the carb cannot keep up with the extra demand for gas, then the engine will die. Good luck with that.

Posted on Nov 07, 2014

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Won't rev past idle.

Sounds like its time for carburator/s clean up, I think the main jets may hve dirt in them.

Posted on May 15, 2009

  • 492 Answers

SOURCE: would rideing around in snow just passed your skid

sounds to me like u r reeving engine too high (running it to hard in low gear)

Posted on Feb 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why would my 660 grizzly pop in & out of forward gear, jus whines, jumpin in & Out ???


Grizzly 660 Shifting problem. - Yamaha Grizzly ATV Forum

www.grizzlycentral.com > ... > Grizzly Engine & TransmissionMar 12, 2012 - 4 posts This is a discussion on Grizzly 660 Shifting problem. within the Grizzly Engine ....2005 grizzly 660 gear position sensor problem.

Aug 17, 2015 | Yamaha 2005 Grizzly 660 Auto 4x4

1 Answer

My 550 grizzly won't idle.seems to run out of gas.starts right up again then kills.can you help?


Clean Maf and check contact at TPS but all that should under waranty , take it to the dealer .

Nov 02, 2013 | Yamaha 2013 Grizzly 550 FI Auto 4x4 EPS

1 Answer

My car has had persistent power issues over the past year. Last winter I replaced my alternator, and the car has ran (decently) since then. However, I began to notice that when the car was in idle (at a...


Get the alternator output checked, it sounds as if there is an issue of power, also be worth having the battery condition checked, regards Mike

Oct 27, 2013 | 1993 Subaru Impreza

1 Answer

1998 tacoma 3.4L sputters then clears up shifting through the gears


Check the throttle positon sensor on the throttle body. You can do that with a meter. Your idle air control turns off when the truck heats up and is the reason you are noticing it more after it is warmed up.

May 26, 2017 | 1998 Toyota Tacoma

1 Answer

Can not shift my 2001 yamaha grizzly out of neutal, wont go to high or reverse, until the outside tempature is above freezing.machine is dry and keeped in shed.


Are your oils up to par and full like case fluid and is your bike reving too high in idle to go into gear also clutch may be engaging spinning the gears well your trying to slip it into gear is there a grinding noise

Dec 26, 2011 | Motorcycles

1 Answer

1998 corolla sputters sometimes in first gear


sounds to me like the Maf sensor is going bad map is the
mass air flow located right after the air box

Aug 04, 2009 | 1998 Toyota Corolla

1 Answer

2008 Yamaha 660 Grizzly???? Help?


try turning your idle down, i have a 98 grizzly 600 and the other day it was cold so i turned the idle up to start it and wen i put it into gear i would drive itself if ur idle screw is in the same place as mine it should be above the engine beside ur left leg turn it left to turn it down wen ur idle is up ur motor is reved to hi wen going into gear hope my advice helps

Jun 29, 2009 | 2000 Yamaha TT 600 R

1 Answer

Shift CABLE?...On my way from Chicago to Milwaukee, my shift stick (automatic) got stuck in last gear, as I tried to pry it from last gear it became losen and stuck in drive. I got home safely but I knew...


Disconnect cable at the trans and try to move the shift lever. If cable moves freely, try to move control arm on trans to make sure it's free. (don't forget,,,do this with engine off and wheels chocked so it dosen't roll away on you!
Chances are the cable is bad.

Feb 18, 2009 | 1998 Chevrolet Cavalier

1 Answer

1984 volvo 240 gl wagon engine kill


Check for vacuum leaks,pull off your intake hose and look for small cracks,also go to the rear of car and listen for you intank fuel pump,needs to making an humming sound,no sound or intermediate this can be your problem.

Jan 24, 2009 | 1984 Volvo 240 Series

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...