Question about 2002 Honda CR 250 R

1 Answer

I had to cut out my swingarm bolt on a 02 cr 250, the bolt seems to be seized in the transmission case and i will have to drill it out, my question is where can i get the replacement bushings that go in the trans? they don't seem to come up on any diagram that i have seen.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Honda Master
  • 2,050 Answers

Ah ha, never greased it hey? It actualy goes through the engine cases, at the rear. I have heard of using a sawzall to cut it between the swing arm and engine case. It is not going to be fun. You may have to remove the engine then, and use a little heat, just be careful. Good luck

Posted on Jul 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yamaha 4HP outboard - cannot pull starter cord - jammed.


Engine or gearcase seized...
Remove the recoil starter ( 3 bolts and the startingear link)
If you can turn the flywheel slightly: Gearcase seized
If you can't turn the flywheel at all: Engine seized.
In both cases: If you can't disassemble and have the job done yourself, forget that motor...

Dec 09, 2012 | Clymer Marine Maintenance and Repair...

1 Answer

Side to side play in front sprocket on 02 cr250r


If you look at the case , you should see a cast spacer in it. If the sprocket "Rocks" on the shaft, you may have some debris on the case mating face (the inside of the sprocket) - remove the sprocket and clean the shaft and mating face to make sure there is no debris. When the sprocket securing nut is fitted, the sprocket should have no noticeable rocking. Make sure the nut is torqued to the correct setting.

Aug 23, 2012 | 2002 Honda CR 250 R

1 Answer

How do I get the impeller for the water pump off


Need to take off the right crankcase cover, hold the pump's gear from inside and unbolt the impeller from the outside.http://www.babbittsonline.com/honda-motorcycle-parts#/Honda/CR250R_A_(02)_MOTORCYCLE%2c_JPN%2c_VIN%23_JH2ME033-2M400001_TO_JH2ME033-2M499999/WATER_PUMP/CR250R-02-JPN-A/2Y14KZ32KZ3AE0400A
The impeller's axle (with the gear) is threaded and the impeller bolts on to it.

Feb 09, 2012 | 2002 Honda CR 250 R

1 Answer

Need to know the torque spec for the plug in a 2002 cr 250r


15lbs with never seize on threads ALWAYS 15lbs with never seize on any aluminum.

Sep 15, 2011 | 2002 Honda CR 250 R

1 Answer

2002 Honda CR 250 R will not shift into 4th or 5th gear


Hi, Doucheonmand and the usual suspects are:
1. Clutch not disengaging.
2. Bent shift shaft.
3. Shift fork bent or seized.
4. Gear seized on the shaft.
5. Gear positioning lever binding.
6. Shift return springs weak or broken.
7. Shift return spring pin loose
8. Shift mechanism arm spring is broken.
9. Shift mechanism arm is broken.
10. Shift drum is broken.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
02 cr250 shifting
no fourth gear
What happened to my 5th gear
CR250 2002 2003 pdf
https://www.partsfish.com/page/oem-parts-for-honda
Honda CR250R Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Nov 17, 2017 | 2002 Honda CR 250 R

1 Answer

Can not remove swingarm pivot bolt


Secure the bike with the rear tire off the ground.

Take the nut off the one side of the pivot bolt.

Now get a rubber mallet or deadblow, and beat that pivot bolt hard a few hits
Don't be afraid to hit it hard, because thats what it'll take to get it out.
DO NOT use a hammer and beat the threads or mushroom the end of the pivot bolt or you'll never get it out unless you cut it off.

use one hand to hold the swingarm while tapping the bolt, which will take a little pressue off the bolt making it slide out with each tap.

Before reassemble, clean the bolt and the threads.

Dec 11, 2010 | 2004 Yamaha YZ 250 F

2 Answers

When I try to start my honda CR 250 the kick start leveler will not go down, it is lick it is frozen or blocked.


I had the same problem, and i was that the shaft that the kick start was attached to had sezied on to the idler gear in side the engine. all i did was drain the oil, remove the cover and replace the shaft and idler gear.

Apr 04, 2009 | 2003 Honda CR 250 R

1 Answer

1998 cr250 bottomend case bolt torq specs


Hello the bolts should be torqued to about 10 N-m , or 7 ft-lbs in an alternating cross pattern

Apr 03, 2009 | 2002 Honda CR 250 R

Not finding what you are looking for?
2002 Honda CR 250 R Logo

357 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5055 Answers

Marvin
Marvin

Level 3 Expert

81294 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...