How do get the head light bulb out

you need to open the bonnet and need to remove the bulbs in the head lights
replace with the new ones the bottom ones are the parking lights so change it correctly dont change the main lights

You don't have to remove the headlight to change the bulb. The bulb can be removed from the back of the headlight, usually by turning the bezel ring that holds the bulb onto the headlight housing. Just make sure you do not touch the glass part of the bulb while replacing it or it will burn out again fast.

Hello first start by opening your engine hood rite behind your head lamp pot is a plug socket simply twist counter clock wise and socket will come out remove bulb and replace turn clock wise to tighten up turn head lights on to check that new bulb works both high and low beam you have now changed your head lamp bulb and restored your lights

You want to change the tail light bulb?

The process for replacing tail light bulbs is the same in all models. If you have a burnt-out tail light bulb, you may need to replace the brake light, the reverse light or the turn signal. The procedure to replace each of the bulbs is the same.

Instructions

1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.


2. Remove the two screws from the tail light assembly. Pull the tail light out and inspect the back for two bulbs. The top bulb is the brake light and turn signal. The bottom bulb is the reverse bulb. Determine which bulb you need to replace.

3Rotate the bulb's socket counterclockwise to disconnect it. Unplug the bulb from its socket.

4Push the replacement bulb into its socket firmly. Insert the socket back into the tail light. Turn it clockwise to secure it in place.

5Place the tail light into its cradle. Hold it with one hand and replace the Phillips head screws with the other.

To replace the headlight bulbs.You need to remove the head light assembly out.The head light assembly is held by 2 to 3 three screws on each side. You need to remove those screws first.The front trim will get loose,the front trim is held by pins.The pins are of plastic and easy to release.Just release this pins and the front trim will get completely loose and can be easily taken off/. The head light assembly is in the front fender.Once the front trim is removed the head light assembly can be easily removed from front fender compartment.If its bit tight there,then you can use a screwdriver to give it a pull towards out.The head light bulbs can now be easily seen as well as easily removed now.Turn the bulb socket counterclockwise to remove the bulb from the bulb assembly. -------- Keep updated for any more queries.Thanks.

1) You will need to open the rear swing door.

2) On the inside jam there are two torx headed screws (T-15's if I remember correctly).

3) Unscrew the two torx screws.

4) The light is now held by two mounting tabs (small spherical headed plastic sets that go through a rubber grommet).

5) You will need to pry the light casing off (easy pressure with a good size flat head screw driver will do the trick).

6) The light bulbs are twist mount settings inside the light casing.

7) Twist out the mount setting, change the bulbs, and reset the light mountings.

8) To put the light casing push the light casing back on and put in the screws. Everything else will work in reverse when it comes to assembling the whole unit.

2006 Jeep Liberty Replacement Light Bulb Sizes
Low Beam Headlamp Bulb Size: 9007
High Beam Headlamp Bulb Size: 9007
Parking Light Bulb Size: 2825 or 3157
Front Turn Signal Light Bulb Size: 3157
Rear Turn Signal Light Bulb Size: 3757ALL
Tail Light Bulb Size: 3157
Stop Light Bulb Size: 3157
High Mount Stop Light Bulb Size: 921
Fog/Driving Light Bulb Size: 9145 or H3-55W
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 3157
Front Side Marker Light Bulb Size: 168
Ash Tray Light Bulb Size: 161
Map Light Bulb Size: 578
Dome Light Bulb Size: 578
Step/Courtesy Light Bulb Size: 906
Trunk/Cargo Area Light Bulb Size: 578

Thank you for using fixya, and good luck

This is problem cant be solved by changing head light. You need to replace wiring of your bike. This problem is occur because of short-circuit in wiring.

you unplug the bulb then there is a "collar" around the light bulb just turn i belinve its counterclock wise and remove the bulb, dont toouch the new bulb reverse the removel to install

you need gloves hands cant touch bulbs .oils from hand causes bulb to blow.to change bulb you raise hood remove head light housing has to be removed before you remove bulb.

Right behind the light there should be 2 clips pull up on those and the headlight will come out to change the bulb