Torque specifications I have torque setting for my rear wheel bearing on Hyundai 2000.it says 75 nm,then to 155 nm but my torque wrench only gos to 130 nm,what am I doing wrong

1. First, tighten all the bolts to 25 Nm (18 lb-ft).
2. Tighten all the bolts to 50 Nm (37 lb-ft) in sequence, starting from the center and working outward.
3. Tighten all the bolts to 70 Nm (52 lb-ft) in sequence again, starting from the center and working outward.
4. Finally, tighten all the bolts an additional 90 degrees in sequence again.

Please note that it's important to follow the correct torque sequence and to use a torque wrench to ensure that the bolts are tightened to the correct specifications. It's also recommended to replace the head bolts with new ones to ensure proper torque and head gasket sealing.

front

1. Install or connect the following:
   • Strut assembly
   • Fork to the strut and torque the bolts to 59 ft. lbs. (80 Nm)
   • Fork to the lower arm and torque the bolt to 88 ft. lbs. (120 Nm)
   • Upper strut mounting nuts and torque to 36 ft. lbs. (50 Nm)
   • Brake hose bracket
   • Front wheel
2. Check and/or adjust the wheel alignment.

--------------------rear------------

To install:

1. Install or connect the following:
   • Strut assembly and mounting bracket and torque the bolt to 36 ft. lbs. (50 Nm)
   • Upper arm and rear carrier bolt and torque the bolt to 88 ft. lbs. (120 Nm)
   • Lower mounting bolt
   • Rear wheel

Yes, I can help you with the cylinder head torque wrench setting for your Hyundai Atos 1.0cc. Here are the torque specifications:

First pass: Tighten all bolts to 18 lb-ft (25 Nm)
Second pass: Tighten all bolts to 45 lb-ft (61 Nm)
Third pass: Tighten all bolts to a final torque of 65 lb-ft (88 Nm)
It's important to tighten the bolts in the correct sequence. The sequence is as follows:

10 6 2 3 7
9 5 1 4 8

Note: The numbers above refer to the cylinder head bolts in the correct sequence. Always use a calibrated torque wrench to ensure that the bolts are tightened to the correct specification.

I hope this helps you with your cylinder head installation. If you have any further questions or concerns, feel free to ask.

I may be unfamiliar with the torque settings for the rear wheel bearing of a Tata Indica with a collapsible spacer. But on a general note, the torque specifications for the rear wheel bearing of a vehicle can vary depending on the specific make and model of the car and the condition of the vehicle.
It is best to consult the factory service manual or a professional mechanic for the accurate torque specifications for your specific vehicle. The manual will have detailed information on the torque settings, and a professional mechanic will have the tools and knowledge to ensure the work is done correctly.
Please note that it is important to use a torque wrench to tighten the bolts to the specified torque to ensure the proper clamping force on the bearing and prevent damage to the bearing or other components.

The main torque setting for the Toyota Corolla VVTi 1.3 engine will depend on the specific component or fastener being tightened. It is important to refer to the manufacturer's specifications or service manual for the correct torque values to use.
Here are some general torque values for common components on the Toyota Corolla VVTi 1.3 engine:

• Cylinder head bolts: 55 Nm (41 ft-lbs)
• Connecting rod nuts: 40 Nm (29 ft-lbs)
• Main bearing cap bolts: 65 Nm (48 ft-lbs)
• Oil pump bolts: 12 Nm (9 ft-lbs)
• Timing chain tensioner bolt: 25 Nm (18 ft-lbs)

It is important to note that these torque values are just estimates and may vary depending on the specific engine and component. Always refer to the manufacturer's specifications for the correct torque values to use.
In addition, it is important to use a torque wrench to accurately tighten fasteners to the specified torque. Using the wrong torque value or over-tightening fasteners can lead to problems such as stripped threads, damaged components, or engine failure.
I hope this helps!

Let me know if you have any questions.

1. Tighten the cylinder head bolts in the sequence shown. Using the 4 step torque turn method, tighten according to the following values:

• • Step 1: All to 34 Nm (25 ft. lbs.)
  • Step 2: All to 68 Nm (50 ft. lbs.)
  • Step 3: All to 68 Nm (50 ft. lbs.)

CAUTION: Do not use a torque wrench for the following step.
Step 4: Turn an additional 1/4 turn

• Step 5: Install and tighten bolts (1-10) in sequence shown, to 41 Nm (30 ft. lbs.) .

1. Tighten bolts (1-10) again to 41 Nm (30 ft. lbs.) PLUS 1/4 turn in sequence shown.
2. Install main bearing bedplate to engine block bolts (11-20), and torque each bolt to 28 Nm (20 ft. lbs.) in sequence shown.

Connecting Rod Cap Bolts 54 Nm (40 ft. lbs.) + 1/4 turn
1997 Jetta: Torque settings..vw..the head, fly wheel, big ends.


1997 Jetta3 1800 feul injection


Vibration Damper/belt Pulley
Tighten 20 Nm (14.8 ft lb) Crankshaft Toothed Belt Sprocket Tighten 90 Nm (66 ft lb) + 90° Camshaft Sprocket Tighten 80 Nm (60 ft lb) Main Bearing Cap
Tighten 65 Nm (48 ft lb) FLYWHEEL TORQUE
Torque 60 Nm. (44 ft. lbs.) + 1/4 turn (90°) [1] [1] Always replace bolts.
CYLINDER HEAD TIGHTENING TORQUE [1] :
1st sequence: 40 Nm (30 ft lb)
2nd sequence: 60 Nm (43 ft lb)
Final sequence: plus 1/2 turn (180°)
Here are some additional specifications, thanks
ntake Manifold
Mounting Bolts 25 Nm (18 ft. lbs.) Bearing Cap Nut 20 Nm (15 ft. lbs.) Rod Bearing Cap
Assembly
Tighten 30 Nm (22 ft lb) + 90° To measure radial clearance
Tighten 30 Nm (22 ft lb) but NOT additional 90° TIGHTENING SPECIFICATIONS
Oil Pump Bolt 20 Nm (14 ft. lbs.) Oil Tube To Block 10 Nm (7 ft. lbs.) Exhaust Manifold to Cyl. Head 25 Nm (18 ft lb) Exhaust Manifold to Front Exhaust Pipe 40 Nm (30 ft lb) Water Pump
TIGHTENING SPECIFICATIONS
Cover Bolts 10 Nm (7 ft. lbs.) Mounting Bolt and Studs 20 Nm (15 ft. lbs.) + 1/4 turn (90°) Pulley Bolts 25 Nm (18 ft. lbs.)

TIGHTENING SPECIFICATIONS
Connecting Rod Nuts:
Tighten In Two Stages:
First Stage 30 Nm (22 ft. lbs.) Second Stage turn an additional 90°(1/4 turn)

Here are the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends:
Main bearings

• Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm
• Main bearing bolts: 45 Nm + 90°

Head bolts

• Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°
• Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Nm + 180°

Big ends

• Connecting rod cap nuts: 1st stage - 22 Nm, 2nd stage - 40 Nm + 90°

Please note that these are just the general torque settings. The exact torque settings may vary depending on the specific engine and vehicle. It is always best to consult your vehicle's service manual for the correct torque settings.
Here are some additional tips for tightening the torque settings:

• Use a torque wrench to ensure that the bolts are tightened to the correct torque.
• Tighten the bolts in a star pattern, working your way from the center out.
• Do not overtighten the bolts, as this can damage the engine.

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

4-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake shoes
     
   • Rear halfshaft nut and loosen the halfshaft from the hub
     
   • Wheel hub and place it in a vise
     
   • Inner wheel bearing race from the hub
     
   • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
     
   • Parking brake cable from the steering knuckle
     
   • Brake line from the wheel cylinder and support the knuckle
     
   • Lower shock absorber nut
     
   • Lower ball joint by holding the ball joint stud
     
   • Upper ball joint
     
   • Coil spring while noting the location of the insulator
     
   • Steering knuckle cam
     
   • Steering knuckle
     
   • Snapring and press out the outer wheel bearing race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

To install:

1. Install or connect the following:
   
   • New wheel bearing into the steering knuckle
     
   • Snapring to the knuckle
     
   • Wheel hub
     
   • Steering knuckle cam and hand tighten the bolt
     
   • Coil spring
     
   • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
     
   • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
     
   • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
     
   • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
     
   • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
     
   • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
     
   • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
     
   • Brake shoes
     
   • Rear wheel
     
   • Negative battery cable
     
2. Fill and bleed the brake system.
   
3. Check and adjust the wheel alignment as needed.
   

2-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake drum
     
   • Wheel hub nut
     
   • Wheel hub
     
   • Inner wheel bearing race from the hub
     
   • Snapring
     
   • Wheel bearing outer race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

     Rear hub removal
     

     Inner wheel bearing removal-rear hub/bearing
     

     Rear wheel bearing removal-2wd
     

     Rear wheel bearing removal-4wd
     

To install:
Install or connect the following:

• Wheel bearing in to the knuckle
  
• Snapring
  
• Wheel hub into the wheel bearing
  
• Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  
• Brake drum
  
• Rear wheel
  
• Negative battery cable
  

  Rear wheel bearing installation
  
  hope this helps if so send testimonial comment or even any other questions you have
  

this is for 2003 7.5 inch ring gear axle. SECTION 205-02A: Rear Drive Axle/Differential — Ford 7.5-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Drive Pinion Flange and Drive Pinion Seal Special Tool(s) 2-Jaw Puller 205-D072 (D97L-4221-A) or equivalent Holding Fixture, Drive Pinion Flange 205-126 (T78P-4851-A) Installer, Drive Pinion Flange 205-002 (TOOL-4858-E) or equivalent Removal

1. Raise and support the vehicle.

1. Remove the rear wheel and tire assemblies.

1. CAUTION: Remove the rear brake calipers to prevent drag during the drive pinion bearing preload adjustment. CAUTION: Do not allow the calipers to hang from the brake hoses. Remove the rear brake caliper and support bracket from the knuckle as an assembly. Wire the caliper and support bracket assembly out of the way.
2. CAUTION: Index-mark the driveshaft flange and pinion flange (4851) to maintain initial balance during installation. CAUTION: The driveshaft centering socket yoke fits tightly on the pinion flange pilot. Never hammer on the driveshaft or any of its components to disconnect the yoke from the flange. Pry only in the area shown, with a suitable tool, to disconnect the yoke from the flange. Disconnect and position the driveshaft out of the way.

1. Install an Nm (inch/pound) torque wrench on the nut and record the torque necessary to maintain rotation of the drive pinion gear through several revolutions.

1. CAUTION: After removing the nut, discard it. Use a new nut for installation. Use the special tool to hold the pinion flange while removing the nut.

1. Index-mark the pinion flange and drive pinion gear stem to maintain initial balance during installation.

1. Using the special tool, remove the pinion flange.

Installation

1. Inspect the pinion flange seal journal for rust, nicks, and scratches prior to installing the flange. Polish the seal journal with fine crocus cloth, if necessary.

1. Lubricate the pinion flange splines.
   • Use SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.

1. NOTE: Disregard the index marks if installing a new pinion flange. Position the pinion flange.

1. Using the special tools, install the pinion flange.

1. CAUTION: Do not under any circumstance loosen the nut to reduce preload. If it is necessary to reduce preload, install a new collapsible spacer (4662) and nut. CAUTION: Remove the special tool while taking preload readings with the Nm (inch/pound) torque wrench. Tighten the nut to set the preload.
   • Rotate the drive pinion occasionally to make sure the differential pinion bearings (4630) (4621) seat correctly. Take frequent differential pinion bearing torque preload readings by rotating the drive pinion with a Nm (inch/pound) torque wrench.
   • If the preload recorded prior to disassembly is lower than the specification for used bearings, then tighten the nut to specification. If the preload recorded prior to disassembly is higher than the specification for used bearings, then tighten the nut to the original reading as recorded.
   • Refer to the torque specification for used differential pinion bearings in the Specifications portion of this section.

1. CAUTION: Align the index marks. CAUTION: Install the driveshaft with new bolts. If new bolts are not available, apply Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 to the threads of the original bolts. CAUTION: The driveshaft centering socket yoke fits tightly on the pinion flange pilot. To make sure that the yoke seats squarely on the flange, tighten the bolts evenly in a cross pattern as shown. Connect the driveshaft. .

1. Install the rear brake calipers.

1. Install the rear wheel and tire assemblies.

1. Lower the vehicle.