Question about 1989 Yamaha TZR 250

3 Answers

1989 Zuma, just rebuilt carb to OEM specs, turned air screw to factory setting, Removed gas cap in case not allowing air. Installed new spark plug. Scooter will fire and run for about 20 seconds then dies. Removed plug and found oil/gas mix on plug. wiped off and re-installed. Turned air screw from position half turn each direction and retried firing. Nothing. Original complaint with scooter was that it would loose power under acceleration i.e. going up hill. ATTENTION HAVE TO SELECT WRONG TYPE OF MOTORCYCLE TO GET TO POST. PLEASE NOTE THIS IS FOR A 1989 YAMAHA ZUMA RAZZ 50CC SCOOTER.

Posted by on

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 375 Answers

Answered

Posted on Jul 01, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Well if it takes mixed gas then its ur carb u might want to try cleaning it real good blow it out make sure nothing is stopped up or it can be getting to much gas and floodong out but if it dont take mixed gas then u have a blown head gasket causing the oil to mix with the gas not allowing it to spark good enuff

Posted on Apr 28, 2012

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Fuel line vacume opperated pull off lines,inside fuel tank tap is like a ball valve stoke n poke till moving freely should work done it but done it since dirty tank.

Posted on Apr 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yamaha Zuma 50/Cold Start Problem


Hi, James and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Float needle and seat sticking.
5. Float level too low.
6. Carburetor bowl vent line clogged/blocked/pinched.
7. Idle adjusting screw set too low.
8. Air/fuel mixture screw set too lean.
9. Idle port, transfer ports, slow air jet clogged.
10. Slow fuel jet clogged.
11. Faulty fuel pump.
For more information about your issue and valuable "Free" downloads that you will need please Click on the links below. Good luck and have a nice day.
ZUMAFORUMS NET View topic 2005 yamaha zuma yw50t cold start issues
My Scooter wont start if engine is cold scooters
https://www.manualslib.com/manual/781192/Yamaha-Cw50l.html#product
OEM parts for Yamaha
Yamaha ZUMA CW50N Owner Manual

Jan 22, 2014 | 2012 Yamaha Zuma 50F

1 Answer

I have a 2 cycle Troy-Bilt TB90BC line trimmer. Won't idle. I've had the carburetor dipped, installed a new carb kit, replace the gas lines, but will only run at full speeds. Dies out easily....


One of three things is occuring here. The IDLE SPEED SCREW (Phillips head) on the throttle plate is screwed in way too far. The L and H mixture screws are open way too much allowing the carb to use excessive fuel, even on startup. Those 2 screws may need adjusting. The metering lever in your carb is not adjusted flush with the carb body flange and is holding the gas needle open constantly. Check these things and post back.

Sep 09, 2011 | Troy Garden

1 Answer

I have a husqvarna 575 xp i can not get It to start and stay running. It has fuel and spark . Good spark but not sure on carb . settings.


the gas in the carb might bad might need to take apart and bolw out with some air and carb cleaner there are very tiny holes and the gas builds up a yellowish scale that can bolck the tiny holes i recomend a carb kit wich will give you new gaskets there are two adjustment screws on the carb if you take the spark plug out and it is wet you are getting to much gas and flooding it out try to turn the screws in if the screws have the little plastic caps on them remove them this will allow you to adjust the gas to the carb there is a hi and low the low is idle speed turn just enough so the chain dosent spin hi hold throttle down and adjust out till it will get wide open and sound clean no missing or struggling. i can post some photos of a chain saw taken apart to help you if you need it . please let me know if ther is any thing else i can do to help

May 25, 2011 | Husqvarna Garden

1 Answer

1997 Yamaha Zuma Super Scoot turn signal flasher not working


Hi, Retals57 I would buy the OEM part to be on the safe side for more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Yamaha CW50L Service Manual
OEM parts for Yamaha
Yamaha ZUMA CW50N Owner Manual
Yamaha Zuma 2004
Yamaha Zuma Wikipedia

Jun 17, 2017 | 2005 Yamaha Zuma

1 Answer

Need to know how to adjust a carb on the 2.5L. I'm having a problem with too much gas getting into the chambers and drenching my spark plugs. I can also smell a lot of gas coming out of the exhaust. I...


the air fuel adjustment has little to do with what u have going on, but here is what u do, make sure the engine is at normal operating temp temperature (at least 185F) then verify idle speed is set to spec +or- 50 RPM, then turn the carb mixture adjusment screw in until the idle speed starts to drop off, then turn it back out until the idle speed increases to its highest point (u will need a hand held tachometer), when u have reached the highest idle turn the idle screw back in 1/4 trun, that is lean best idle.

Mar 19, 2010 | 1985 GMC S-15

1 Answer

Wont idle unless i havethe throttle barley turned


The idle circuit is still plugged up or it would not be giving you this problem. Remove the carb and dis-assemble it then soak the parts in denatured alcohol for 30 minutes. Then use a spray carb cleaner to finish the job. Spray into all the little holes in the carb body. Especially spray into the air screw and throttle screw holes. Reassemble the carb and LIGHTLY seat the air and throttle screws then turn each of them one and one half turns outward. This is the factory setting. Before putting the slide back into the top of the carb, move the clip on the jet needle one notch lower on the needle. This will richen the low end fuel mix. Install a new spark plug and clean the air filter. Please rate my answer. Thanks.

Feb 08, 2010 | 2003 kawasaki KX 125

1 Answer

1989 Zuma, just rebuilt carb to OEM specs, turned air screw to factory setting, Removed gas cap in case not allowing air. Installed new spark plug. Scooter will fire and run for about 20 seconds then dies....


Half a turn is too much - 1/8th at a time.
Check for air leaks at manifold - both at crankcase and at carb ends.
Does it run (idle) on its own, or do you need to keep on the throttle?
Have you checked the other end (the exhaust!) as well? A blockage there will be as bad as a lack of fuel at the front end.
Make sure you have everything in place - air filter, etc. - as with those little 2T engines, they are far more susceptible to thigs like that than a bigger engine.

Jul 01, 2009 | 1989 Yamaha FZX 750

Not finding what you are looking for?
1989 Yamaha TZR 250 Logo

763 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...