Question about Suzuki Boulevard C50 Motorcycles

1 Answer

Cant set the carb right how many turn for both it is a 2 stroke jr 50

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

On fuel/air mixtire you turn it all the way in till it stops then back out 1 1/2 turn to set air / fuel mix

Posted on Jul 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant find manual on line


what machine is this for?? i doubt you put 4 stroke in with the petrol!! usually you mix 2 stroke oil with unleaded fuel at a ratio of 50-1
so 100ml of oil in 5 litres of fuel. If your trying to completely remove the striming head then usually they are a left hand thread, so turn it clockwise to undo it

Mar 08, 2015 | Garden

1 Answer

How to install a 50 cc carburetor on a 4 wheeler


best place t go is youtube and if you cant find your watching any small motor video will help but you need to watch one of the same engine if yours is 2 stroke then watch a 2 stroke video and same as 4 stroke carbs are different hope this helps

Sep 16, 2014 | ATVs

1 Answer

How do i set timing on a 1996 mariner 40 hp 4 cylinder 2 stroke outboard?


timing marks on flywheel and a pointer above the carbs , under the flywheel there is an adjustable rod from the trigger to the throttle linkage ! strobe light required , cant remember timing off top of my head as out so google it !

Aug 21, 2013 | Clymer Marine Maintenance and Repair...

1 Answer

Rich mixture problems


turn the air screw in or out to try and correct on the carb. if that doesn't work it might be the altitude for where you are at you may have to change jet sizes in the carb or adjust the needle up or down also make sure the air filter is clean.

Jul 11, 2013 | 2005 Suzuki JR 50

1 Answer

Chain saw carburator settings for husqvarna 61


Turn both screws CW to stops (lightly), then back out CCW 1-1/2 turns each. This is a basic setting and the engine should start and run. Allow the engine to warm up, then pull the throttle full on. Turn the H jet screw CW until the engine starts to speed up, but still 4-strokes. Proper adjustment occurs when the engine is 4-stroking, but immediately 2-strokes when cutting. This gives best power and lowest heat. Release the throttle and adjust L jet CW until the engine idles fairly well, but will allow the engine to 'follow the throttle'. Adjust idle speed screw so that the chain stops turning, but the engine continues to run. Hope this helps!

Jun 06, 2010 | Husqvarna "Chain Saw - 16" Bar, 3 Hp

1 Answer

Hi i have a viyality 50 2 stroke issue is wh...


its still a carb fault!!! but its a blocked running jet
so strip out the carb and clean out all the jets
dont go poking wire into any of the jets as you will only distroy them that way,,,use carb cleaner and comprest air if you can check you have a good flow of gas getting through the carb then re-fit the card and run the engine up then tune it when warmed up

May 20, 2010 | Motorcycles

1 Answer

Cant get choke to operate on C50TLRY 2000 50 hp 2


Check choke itself to make sure it moves freely. Adjust the cable and spring if necessary. If the choke is controlled by a vacuum controlled actuator, make sure it is not leaking or loose pressure

Sep 09, 2009 | Boating

1 Answer

What are the factory settings for the l & h needle valves on the 25cc carb?


usually 1 1/2 turns from snug in will be right. this is true on most all 2 stroke engines and 4 stroke that use a diapraham type carb

Jul 07, 2009 | Craftsman 25cc Gas Line Trimmer

3 Answers

Cant keep my RM 250 2 stroke running


DOES IT STOP RUNNING BECAUSE OF A FOULED PLUG WHAT RATIO FUEL/OIL ARE YOU RUNNING
40:1 IS A GOOD RATIO NEVER HAD A FAILURE IN 20 YEARS

Apr 13, 2009 | 2005 Suzuki RM-Z 250

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...