Question about 1991 Honda ST 1100 Pan European

1 Answer

Front brakes binding after replacing calipers and brake pads and bleeding 1996 model

Posted by on

  • Z Laws May 11, 2010

    Why did you bleed them for a brake pad replacement?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Honda Expert
  • 139 Answers

Replace the caliper seals and clean up the pistons clean the grooves that the seals sit in then refit and bleed the system problem will be sorted

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brake fluid


pull the caliper off u will need a c clamp remove the new pads using 1 of the old pad position it againest the caliper piston DO NOT LOOSEN THE BLEEDER SCREW loosen the reservor cap slightly
position the c clamp on the caliper using the end that turns againest the old brake pad push the piston down into the caliper until the c clamp is tight remove clamp and install new pads position caliper and new pads on cycle tighten to specs also when u push the piston in the caliper u might see a little brake fluid coming from the reservoir dont panic this is perfectly normal' now fill reservoir if needed apply brakes slowly and release wait aprox 5to 10 seconds allowing thystem e reservoir piston to return to its resting place keep repeating this procedure and you will begin to c the caliper slowly moving into place giving you braking power again after the brakes pump up hold down firmly on them use a boxed in wrench and quickly loosen the bleeder screw and tighten it back this will remove any air from the system u will notice the brakes get firm faster now check your brakes if u want them to apply faster perform the bleeder screw procedure again this should take care of the problem good luck

May 18, 2014 | 1999 Honda CBR 600 F(4)X

1 Answer

Brake problem on carice 2004


make sure the front brake pads are moving i see them bind on the slides so the caliper works but not the pads

Aug 05, 2012 | Cars & Trucks

1 Answer

1999 Yamaha Kodiak Front Disc Brake - Rebuilt master cylinder with new parts. Replaced orings on piston in front caliper and bleed brakes using new fluid. The piston will not retract. What is proble


The brake hose is clogged. When under pressure from applying breaks, the piston is forced tight to the rotor. When released the fluid will not return through the hose because there is no real pressure. Replace the hose.
murf427

Jul 31, 2012 | Cars & Trucks

1 Answer

How can I change the rotors and brakes on a 2006 Cadillac?


Front brake
Step 1: Identify Front Disc Brake Components
brake_pads_rotor.jpg
Front Wheel Drive Brake Assembly
Most front disc brake components include: brake rotor, brake pads, brake caliper, caliper mount and brake flex hose. Brake service usual occurs between 20,000 and 40,000 miles depending on driver habits, road conditions and brake pad/ rotor materials used.
Step 2: Remove Brake Caliper to Replace Pads
brake_pad_set.jpg
Removing Brake Caliper Mounting Bolts
Locate primary caliper mounting bolts; apply wrench pressure counter-clockwise (When looking at the head of the bolt) to remove the bolts, upper and lower. Make sure the bolt threads are in good shape and replace if necessary.
Step 3: Remove Front Brake Caliper
remove_brake_caliper.jpg
Remove Front Brake Caliper
After removing the primary caliper mounting bolts lift the brake caliper off of the rotor and then tie or secure to the side, being careful not to bend or kink the brake caliper flex hose. Thoroughly inspect brake caliper and brake hoses for leakage, cracks or chaffing and replace as needed. Next remove the brake pads (If not mounted in the caliper) and secondary caliper mounting bolts. Notice how great protective gloves work, most technicians use them on the job today.
Step 4: Remove Brake Pads
remove_brake_pads.jpg
Remove Front Brake Pads
Once the brake pads have been removed, make sure if there is anti rattle hardware to transfer to the new brake pads. Some brake pad manufacturers will include the proper lube (Caliper slides) and anti-rattle hardware to ensure proper performance of their product.
Step 5: Remove Caliper Mount
remove_brake_pads_holder.jpg
Remove Caliper Mount Bracket
Finish removing secondary caliper mount bolts and remove caliper mount. Note: clean and lube caliper slides and pad friction surfaces of all foreign material or build-up.
Step 6: Remove Brake Rotor
brake_rotor.jpg
Remove Brake Rotor
With the caliper mount out of the way you can now remove the brake rotor. Sometimes it can get stuck so you may need to tap it with a hammer or use penetrating oil to free it up. Some manufacturers use small screws to hold the rotor on as well. Clean and inspect wheel studs, replace if any are damaged. Also clean bearing hub rotor mount surface to ensure the proper mounting of the new brake rotor. Inspect the ABS sensor wheel for cracks or damage and replace as needed.
Step 7: Depressing the Brake Caliper
compress_caliper.jpg
Resetting Brake Caliper
To install the new brake pads you must retract the brake caliper piston. Remove the master cylinder lid or open the brake caliper bleeder screw to allow excess brake fluid to be released if necessary. Install C clamp tool and gently tighten clamp until caliper piston is fully depressed. Note: use old brake pad to protect the caliper piston. Close the bleeders once the piston is retracted completely
Step 8: Installing New Brake Rotor
new_brake_rotor.jpg
Install Brake Rotor
Install new brake rotor, the new rotor is manufactured with a protective film over the rotor to keep it from rusting, remove protective film with brake cleaner before installing; also after the brake job is complete you may experience a small amount of smoke from the rotor when first used. This is normal and will go away after the first couple of uses.
Step 9: Installing New Front Brake Pads
new_brake_pads.jpg
Installing New Brake Pads
Reinstall the front brake caliper mount, and then install front brake pads. Make sure the pads are seated properly in the caliper mount; it must be a close fit to work properly..
Step 10: Reinstall Front Brake Caliper
front_brake_rotor_pads.jpg
Re-Install front Bake Caliper
Reinstall front brake caliper and reinstall caliper-mounting bolts, recheck all mounts and mounting bolts. Check the caliper slides to be sure there is no bind and that the caliper moves freely back and forth on the caliper slides. Bleed brake system per manufacturer's specifications to relieve any air trapped in the system. Before driving the vehicle, push the brake pedal down and let it up slowly, repeat until normal brake pedal operation resumes, this operation is forcing the brake pads to travel to the brake rotors.

Dec 18, 2010 | 2006 Cadillac STS

1 Answer

Replaced master cylinder, front brake calipers and rear calipers,


BY TRUCK HAVING ABS BRAKE.YOU NEED A SCANNER TO BLEED BRAKES THE SCANNER HAS TO RESET OPERATION OF THE BRAKE HYDRALIC SYTEM BEFORE YOU CAN BLEED SYSTEM.

Jul 13, 2010 | 2005 Ford F 350 Super Duty

2 Answers

After replacing drive side caliper, both front disk brakes, and rear drum brakes, bleed all three lines, both my front calipers lock grinding my front brakes. I am going to re-bleed my lines tomorrow but...


I assume you mean that you replaced the front pads and rear shoes. Or did you also replace the disks and drums?? Either way you should be ok unless you also replaced the slave cylinders on the rears.
The fluid flows back up to the Master Cylinder as you squeeze the calipers and the slaves to fit the new parts in. Some people pre-fill the caliper to reduce the amount of air and make bleeding easier.Now .....Grinding better be a wrong choice of words. Possibly you spilled fluid on the pads while bleeding the lines. This will cause a binding and shuddering when you apply brake pressure. This will also make you think the lines are not bled properly because of the increased pedal pressure you are putting on the wet/lubricated front pads. If so, replace the pads. Don't try washing them with aerosol cleaner cause it takes more time and money than simply changing them.

Oct 04, 2009 | 2004 Saturn VUE

2 Answers

How do I bleed the front brakes on a 2004 audi a4 quattro?


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Oct 01, 2009 | 2004 Audi A4

1 Answer

Replced front brake pads and calipers adjusted


Bleed the master cylinder first. You have to do that before you belled any calipers or wheel cylinder.

Feb 22, 2009 | 1994 Toyota 4Runner

1 Answer

Front brake pads for 1997 ford ecscort encore


The binding of the brakes is causing the pads to overheat, which is causing the smoke. You need pull the wheel and check things out. Your caliper must be bad (not releasing). You need to replace the caliper, brake pads, and have the rotor cut (a full service parts store or shop cuts the rotor perfectly smooth on both sides), or replaced (it may be cheaper to just buy a new rotor). You should also always change the pads (and check everything else) on the opposite side. So, if u do the brakes on the driver side front, always do the front pass. side at the same time, likewise if u do rear brakes.
Whenever you do brakes u should also flush out the brake lines (by bleeding the brakes) until the brake fluid flows absolutely clear. Old brake fluid is the #1 reason for caliper failure. I've seen many times people replace brake components w/out changing the brake fluid, only to have the brakes wear out very quickly, or not function properly. good luck! hope this helps> please rate this!couontrycurt0

Oct 12, 2008 | 1998 Ford Escort

Not finding what you are looking for?
1991 Honda ST 1100 Pan European Logo

Related Topics:

706 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...