Question about 1978 Honda GL 1000 (K3)

1 Answer

How to hook up the starter cylanoid wiring - 1978 Honda GL 1000 (K3)

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Honda Master
  • 3,433 Answers

Looks like a land mine? Two big terminals and one small? The small is the start, It closes the two big. So, small connected to wire that comes from start button. Batt positive to one large pos. and other large post to starter post. Done.

Posted on Jul 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a question about my 2003 gmc seirra 6.0l. When I turn the key to crank the engine it struggles for a second then starts. It has the same sound as if the battery is almost dead, but I just replaced...


Might be a fuel delivery issue. You can rent a fuel pressure test kit from most parts stores. see if the pump pressures are correct or if the regulator is bad.

Nov 01, 2013 | GMC Safari Cars & Trucks

1 Answer

1966 ford pickup f-100 352 motor will not start


check wire goes from ignition to starter if no power when trying to crank then replace the wire with a new one its easier ok

Nov 12, 2012 | Cars & Trucks

1 Answer

1996 nissan maxima is eating cylanoid switches


If "tapping" the SOLENOID ever worked... you
HAVE A DEFECTIVE SOLENOID.

Defective is all inclusive... and when "STUFF"
happens (burns up)... it is VERY LIKELY to cause
COLATERAL damage...

(FRIED WIRES & IGNITION SWITCH)
((fix that "STUFF" later)).

At the SOLENOID ... apply "B" battery DIRECTLY
to the "S" terminal of the SOLENOID...

IF it does not fully spin up the starter 100% of the time
the solenoid or the starter is DEFECTIVE.

Apr 14, 2017 | 1996 Nissan Maxima

1 Answer

Starter cylanoid just replaced,now no power to anything


You might have not hooked up the main hot wire right. It is a large cable that goes from the battery to the solenoid. Make sure all connections on the battery are tight and clean.

Jan 03, 2011 | Ford Bronco II Cars & Trucks

2 Answers

Sparking under vehicle when trying to start. It has a new battery and new cylanoid.


That sounds like a loose cable from the ignition solenoid down at the starter, or the cable between the starter and the starter solenoid is exposed and touching metal ground on the vehicle. Check the condition of the cable to the starter and also be sure that it is tight, and not touching any metal ground surfaces on the vehicle, and if there is nothing wrong with either then the starter is most likely is faulty.


89e75d5.jpg

Sep 26, 2010 | 1983 Ford F150

2 Answers

No electric power, only to feed side of cylanoid


There is a fuseable link on the heavy wire, not the battery cable, going to the hot terminal of the solenoid. That heavy wire (about 12 gauge) supplies power to the vehicle. Take a test light and probe the wire on both sides of that fuseable link (it says fuseable link on it). If you don't have power on the vehicle side of that link, that's part of the problem. Now you have to figure out why it blew. It may have just corroded off, I've seen that happen.

Dec 03, 2009 | 1987 Ford Ranger

1 Answer

I have a 200 lc hitachi excavator replaced starter 3 weeks ago now machine is clicking the cylanoid beside the batterys and wont roll over


check battery connections at the terminals and at the ground point poor connections will kill starters and Oh so much more good luck

Oct 05, 2009 | Heavy Duty Associated Equipment 6002B...

1 Answer

Is there a reset switch on 2007 gsxr 750. wont start


You have some crushed wiring along the frame. Check the wiring from the switch along the frame under the seat for a rub or a pinch in the insulation. It has a short causing the lights to flash.

Sep 24, 2009 | 1996 Suzuki GSX-R 750 T

1 Answer

I have a 99 grand am and have the starter hooked up but car wont


you have the switch wire on the wrong cylanoid post switch the little wire and try agin

Jul 06, 2009 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
1978 Honda GL 1000 (K3) Logo

Related Topics:

345 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...