Question about Victory Kingpin Motorcycles

1 Answer

I need to know how much play is allowed on the drive belt of a 2004 victory kingpin so I can adjust it properly.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 375 Answers

Are you ready, let get started. For the Drive Belt Inspection it is recommended that you inspect the drive belt annually, and replace at specified intervals regardless of belt condition.

1. Periodically inspect the drive belt for cuts, missing teeth and excessive wear.

2. Adjust the drive belt tension at intervals in accordance with your motorcycle owner's manual (M.O.M.)

To perform the actual belt tension inspection, perform the following:

1. Secure the motorcycle in an upright position. Shift the transmisison into neutral and be sure to elevate the rear wheel off of the ground. This is critical when checking belt deflection or adjusting the belt.

2. Now you need to finf the "tight spot" on the belt. do this by measuring the belt deflection at 4 different spots on the belt as you rotate the rear wheel.

3. Place a mark at the tightest point. Now adjust the belt deflection to specification.

4. Place a tape measure or ruler next to the drive belt to help you measure deflection. Note that some motorcycles, especially the Victory models, have grduations on the belt bracket for reference. Be sure to measure 1/2 way between the front and rear sprocket centers on the lower part of the belt.

5. Use a belt tension guage. These cost about $30.00 and are well worth the expense. Plus you get to add a new tool to your tool chest. Note that the belt tension guage must be kept at a 90 degree angle to the belt to get an accurate measurement.

6. Push up on the belt tension tool measuring the deflection distance with the amount of force required to be in tolerances. In the case of the Victory Kingpin, this is 10 pounds of force with a tolerance deflection of 9mm. 9mm @ 10lbs. force.

Before you do the Belt Tension Adjustment, you need to make sure the wheel alignment is correct. The following with give you instruction and tips on aligning the wheel and belt correctly.

Belt/wheel alignment method 1:

First measure from the center of the swingarm pivot to the center of the axle. Keep it the same on each side. I have Been doing this on dirt bikes for many years and has not failed yet. I use the Motion Pro belt tensioning tool.

Belt/wheel alignment method 2:

This is what I do if I change a tire or belt.

1] Loosen adjusters completly slide tire to front of adjustment slots.

2] run in both adjusters till they just touch

3] Count threads to make sure they are even

4] going 1/2 turn per side. Take the belt to just loose of adjustment

5] Tighten axle nut,and spin wheel about 10 times. To check belt tracking.

6] If belt is to far right loosen the axle tighten the left side an aditional 1/2turn. Opisete for belt to far left.Spin again. You will never get it centered only to where it has a gap on both sides.

7] tighten both sides equaly until you have 9mm of deflection at 10Lb force. At the tightest point

Posted on Jun 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 victory v92c belt adjustment


Hi, Walt for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Victory, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Drive belt tension question
Information on Victory Vision Victory Vegas Victory Kingpin Victory Hammer...
drive belt adjustment
Motorcycle Repair Inspecting Adjusting the Final Drive Belt on 2008 Harley...
Victory Motorcycles Classic Cruiser 2002 Service Manual

Jul 10, 2016 | Victory Motorcycles

1 Answer

How to replace the rear back brakes on a victory 2004 touring cruiser


Hi, Jose sorry you can't find the first and best tool you ever bought for your Victory despair not for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Victory Motorcycle Brake Pad High Performance BREMBO Rear Victory Only...
Information on Victory Vision Victory Vegas Victory Kingpin Victory Hammer...
Witchdoctors How to Replace Rear Brake Pads on Victory Motorcycle
https://www.tradebit.com/usr/mubiz/pub/9003/2004_Victory_Polaris_Touring__Cruiser_Classic_Cruiser_Service_Manual_PR_.pdf
Owners Manuals Victory Motorcycle

Apr 20, 2016 | Victory Motorcycles

1 Answer

Brake and tail light voltages on 2008 victory taillight led


Hi Richard, should be 12 volts and I am sorry you can't find the first and best tool you ever bought for your Victory but despair not for a mere $10 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
DOWNLOAD 2008 Victory Kingpin

Nov 10, 2015 | 2008 Victory Kingpin

1 Answer

What is the fuel pressure specs. for a 2005 victory motorcycle ness kingpin.


Good afternoon. Since all Victory engines were the same in 2003-5, the 2004 Vegas/Kingpin manual I have specifies a pressure of 3.37 BAR (338 kPA) or 49 psi.

Jul 18, 2014 | Victory V 92 C Deluxe Motorcycles

1 Answer

Victory kingpin charging system test


Hi, Anonymous one word "incompetence" if you take your bike to a dealer for a specific issue that costs outrageous amounts of money only to have the same problem 2 days later your situation is not unique unfortunately and it is a double edged sword. First, you suffer the emotional stress and frustration of spending all your hard earned "Drachma" and your bike does not get fixed. Second, comes the realization that not only are the technicians incompetent but also the service manager for not doing anything about it, this isn't rocket science, it's a glorified lawn mower engine with extra cylinders and carburetors sometimes. You need to put an end to all the double talk, dancing around the issue, and a "we don't care attitude", but how you ask, very simple you exercise the "nuclear option" go back to the dealer and ask to speak to the owner or general manager if the owner is not there, then with a straight face and polite voice you ask him/her if they can provide you with the name and contact phone number of the person at your brand motorcycle headquarters in your country that can recommend a repair facility that will fix your bike because your local dealer either can not or will not. I guarantee you that is all the grease you need to get someone to light a fire under the proper persons rear end to resolve your issue "toot sweet" For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
help with charging system 2000 v92sc
http://racetechelectric.com/files/pdf/rte_troubleshooting_flow_chart.pdf
03 06 Kingpin Vegas 8 Ball Ness Vegas Ness Kingpin Service Manual pdf
Motorcycle Service Parts Part Finder Victory Motorcycles Store
Victory Motorcycles Kingpin 2004 Manual

Jul 08, 2017 | Victory Kingpin Motorcycles

1 Answer

Drive belt diagram


Go to a dealer & buy a service manual

Aug 25, 2013 | Victory Motorcycles

1 Answer

2006 Victory Kingpin bucking at low speeds


VICTORY OF CAROL STREAM

26 Miles Away
  • 106 N Schmale Rd
  • Carol Stream, IL 60188
  • 630-690-3333

Jun 09, 2013 | Victory Motorcycles

1 Answer

2004 victory kingpin short


I have an 2005 Victory Hammer. While I was riding last weekend, the OD light will came on and stay on for a while then it went off. About 30 minutes later, it came back on again. Can anyone tell me what is wrong with my bike before I take to the dealer? Thank you.

May 03, 2012 | 2005 Victory Vegas

1 Answer

2004 kingpin took tank off for paint now wont start have fire to spark plugs sounds like not getting any fuel


Hi Aba3chief, check to see if your fuel tank vents are clogged. Good luck and have a nice day.

Sep 04, 2011 | 2005 Victory Kingpin

2 Answers

Rear brake light wiring diagram for 2005 victory kingpin


http://www.carlsalter.com/motorcycle-manuals.asp

Jun 24, 2009 | 2005 Victory Kingpin

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

1,432 people viewed this question

Ask a Question

Usually answered in minutes!

Top Victory Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Joseph Hoffmann

Level 3 Expert

1702 Answers

Are you a Victory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...