Question about 2011 PGO PMX Naked 110

1 Answer

Will not start 2011 PGO PMX ***** 110

Start engine repair @

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • PGO Master
  • 55,806 Answers

Hi, Anonymous and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Scooter Troubleshooting Scooter won start All about Scooters
What To Do If Your Motorcycle Doesn Start
http://git.onelivemedia.com/pgo_pmx_scooter_pdf_service_repair_workshop_manual.pdf
https://www.scootertuning.ca/en/5009-pgo-pmx-110
https://bikez.com/motorcycles/pgo_pmx_110_2011.php

Posted on May 15, 2019

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tapping noise in engine


What's That Ticking Sound Coming From Your Car's Engine?

www.popularmechanics.com/.../whats-that-ticking-sound-coming-from-...
Apr 18, 2014 - My engine has developed a strange ticking sound. Its whisper-quiet before an oil change, and then makes a loud tapping after a new filter and ...

Engine Tapping - Auto Repair Help

www.auto-repair-help.com/auto_diagnostics/engine_tapping.php
ENGINE MAKES TAPPING NOISE WHEN STARTED by Mark Davidson. SYMPTOM SUMMARY The engine emits a tapping noise on start up. The noise may ...

Engine Ticking Clunking Noise - Repair - YouTube

? 9:37
https://www.youtube.com/watch?v=ilDtnJi_BS0
Mar 15, 2013 - Uploaded by knurlgnar24
One of my vehicles started making a rather disturbing sound so I went to investigate and to hopefully fix it.

Dec 02, 2015 | Cars & Trucks

1 Answer

Will not start


If the check engine light does NOT come on when cranking at the times when it won't start, then your ECU is in need of repair. The engine will only start after the check engine light comes on and the ecu is what controls that. It's likely going bad, causing the delayed start problem typical of early 90's jeeps. Repair or replacement services for your jeep ECU are available on ebay.

Sep 03, 2012 | 1994 Jeep Grand Cherokee

1 Answer

Car doesn 't start


If the check engine light does NOT come on when cranking at the times when it won't start, then your ECU is in need of repair. The engine will only start after the check engine light comes on and the ecu is what controls that. It's likely going bad, causing the delayed start problem typical of early 90's jeeps. Repair or replacement services for your jeep ECU are available on ebay.

Aug 06, 2012 | 1995 Jeep Grand Cherokee

1 Answer

Cranks, but won't start


Could be the crank sensor is bad but If the check engine light does NOT come on when cranking at the times when it won't start, then your ECU is in need of repair. The engine will only start after the check engine light comes on and the ecu is what controls that. It's likely going bad, causing the delayed start problem typical of early 90's jeeps. Repair or replacement services for your jeep ECU are available on ebay.

Aug 01, 2012 | 1995 Jeep Grand Cherokee

1 Answer

Have to turn the ignition on and off several times to get the fuel pump working


Your Jeep ecu is in need of repair. Your jeep is having a common problem known as the "Delayed check engine light" starting problem. Next time you try starting the jeep and it the fuel pump won't prime, look at the dash.....the check engine light is not on and the fuel pump will not come on until the check engine light eventually come on, on the dash. Have it repaired and it will eliminate the delayed check engine light start problem.

Aug 15, 2011 | 1995 Jeep Grand Cherokee

1 Answer

How do you remove the "Service Engine Soon" on a


the check engine light alerts you that there are problems. There will be a code or codes stored in the engines computer. You can retrieve these codes one of three ways.

1. call your local auto parts store. Many times they will do this for free.

2. buy an inexpensive code reader. Available just about anywhere that has an automotive department. They will start at about $50.

3. Bring it in to a shop to have a check engine light diagnostic done.

Once you know the code you can then start to focus on a repair. Once a repair is made the codes will be cleared and the check engine light will turn off. If you do not make the repairs the light will not stay off. It will continue to come on and stay on until the proper repair is made.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Mar 08, 2011 | 2001 Pontiac Grand Am SE

1 Answer

Clicking sound then when it stop the check engine light come on. it will not start until the clicking sound stop. previous owner rewired the truck and add a sound system including a big speaker


Your jeep ecu needs to be repaired. You have what is known as the 'No Check Engine Light" no start relay clicking problem. Have the ecu either repaired (a lot cheaper) or replaced. That will eliminate the delayed check engine light and wait time to start.

Feb 17, 2011 | 1994 Jeep Grand Cherokee

1 Answer

95 jeep laredo distribution box keeps clicking then jeep . doesnt start till check engine light comes on


Your jeep ecu needs to be repaired. You have what is known as the 'No Check Engine Light" no start problem. Have the ecu either repaired (a lot cheaper) or replaced. That will eliminate the delayed check engine light and wait time to start.

Feb 15, 2011 | 1995 Jeep Grand Cherokee

1 Answer

How do I remove the bolt on the pulley to replace timing belt on a 95 honda accord


This is a repair best left to the experts. Severe engine damage will occur if the repair is done incorrectly. The Chilton's manual is fine for someone who has a good baseline of knowledge to begin with. But if you do not know what you are doing, it does not provide enough information. Remember this is an INTERFERENCE engine. Do this repair incorrectly, and when you attempt to start the engine, you will more likely than not, cause internal engine damage. If it were a non-interference engine, I would say, give it a try and if you make a mistake, the engine would just not start, but no damage will be done. Not the case with this engine. Your decision.

Jun 14, 2009 | 1995 Honda Accord

Not finding what you are looking for?
2011 PGO PMX Naked 110 Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top PGO Experts

Marvin
Marvin

Level 3 Expert

84619 Answers

ray gallant
ray gallant

Level 3 Expert

62962 Answers

Darrin P. De May

Level 3 Expert

665 Answers

Are you a PGO Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...