Question about Honda CR 125 R Motorcycles

1 Answer

Hoe to know a defective disk plate

Hoe to know a defective disk plate

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Honda Master
  • 2,050 Answers

A clutch disc should be smooth on the surface, no groove cut into it by the friction plate. If you can catch a finger nail on it, it's bad.
The friction plates usually last longer than the discs, but if the discs are bad, replace the whole set. The fiber plates are bad if they look burnt or the fiber has worn down to the disc. If you have a slipping problem, chances are good that it's worn, but check your basket for wear. The tabs get grooved where the clutch plates ride on them!

Posted on Jun 29, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What does e01 mean on ninja 3 in one cooking system

EO1" occurs when the unit is still on but the pot has been removed from the cooking housing system. Place the pot back in the cooking unit.
This can also occur for the following reasons:
-if there is food jammed in the gap between the disc and the surrounding heating plate (the blade circle).
-if there is food stuck to the bottom of the pot.
-if there is food stuck on the heating plate (yes even a grain of rice can be a problem!)
-there is mechanical damage to the unit (disc is defective for instance).
-if the handles on the pot got bent down (so the pot is not fully seated on the heating plate and disc does not get pressed)
-debris or other damage preventing the pot from make full contact with the heating plate.
A good tip is to plug in the unit and turned to any mode. Please be sure the unit is completely dry. Use your finger to fully press on the disc and see if EO1 goes way. If pressing down does not clear EO1, then unit is defective.
If EO1 does clear by finger but does not clear when pot is installed - and bottom of pot, heating element and gap between the disk and heating plate are clear, then the unit is defective.

Dec 29, 2016 | Washing Machines

1 Answer

Where is the serial number located on a john deere 510d i can find out the year of the backhoe

Diane, JD 510D VIN# Location: On older models plate is attached on outside of frame behind either left or right front wheel. On newer models VIN plate is attached just above left (Highway) side cylinder arm. Same location as Caterpillar. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Thread where is Serial number for 1977 John Deere 510 hoe
Serial number plate location for john deere 510d backhoe Google Search

Jun 20, 2016 | John Deere Garden

1 Answer

I have to replace all askspecs of my parking brakes on a

lever kit works the emergency (mechanical) brakes..the parts tore should have an assembly picture of this setup..there is also an exploded parts view of this should show how it goes..

Dec 14, 2013 | 2000 Ford Expedition

2 Answers

Clutch removal and reassembly

last time i changed that part i went to U-tube and found a video someone posted and watched it for an easy solution

Jun 04, 2012 | 2004 Mitsubishi Outlander

1 Answer

Normal dinner plates hit the top washer arm in Bosch dishwasher


Feb 11, 2010 | Bosch 24 in. SHE44C02UC / SHE44C06UC /...

1 Answer

Cannot engage clutch

Possible causes are many. Examples: Worn/damaged synchronizers inside the transmission, worn/damaged engagement sleeves inside the transmission, clutch master cylinder low on fluid (pumping air instead of fluid due to leakage of fluid in the system, i.e., master/slave cylinders or lines/hoses), broken/defective throw-out bearing, broken/defective pressure plate/disk, etc.
Solution: Tow vehicle to Hyundai Service Center & pay diagnostic fee. Then you will know EXACTLY what the problem is and what's required to fix it.

Jun 06, 2009 | 2001 Hyundai Elantra

2 Answers

Clutch snatching

i think it is normal every clutch on each car feels different if it is not slipping i would not worry about it THE CLUTCH IS IN GOOD CONDITION

Dec 12, 2008 | 1991 Volkswagen Corrado

1 Answer

Starter Key Does Not Work

The starter solenoid contacts are burnt or the starter is defective, changing the starter using a ford rebuilt is about an 1 hour job and very easy, but you will need a floor jack and safety stands.

Nov 24, 2008 | 1996 Ford Mustang

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4982 Answers


Level 3 Expert

80339 Answers


Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides