Question about 2001 Yamaha V Star 1100 Classic

1 Answer

Where is the air/fuel mixture screw

Has the slightest poping noise in exhaust ans want see if adjusting will remove.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

A “very helpful” rating for this answer? Thanks!

where is the air/fuel mixture screw - 690eecb.gif

Posted on Jun 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Noise when raving my ford bantam what could that be tried checking my exhaust for licks...


It depends on what kind of noise you hear .
If its a loud noise poping check for holes in the pipes muffler or connections that are bolted like the y pipe to the cat ford also has a tube that off the cat running to an AB valve from the air pump in general inspect the exhaust system mounts as well .
If you hear like a rattling kind of noise that likely is the converter on the way out they will do this before they clog.
Don't mistake it for a lose or missing mount take a good look before you start buying parts but if you need parts the best way is do it all do it once then you are good for 5 or 6 years.

May 27, 2015 | Ford Cars & Trucks

1 Answer

Its making a poping noise out the exhaust and it cuts back when i give it gas


Hi, Anonymous popping or backfire on deceleration is usually caused by a lean fuel condition or an air leak in the exhaust system and is generally located where black carbon soot is seen as a flashing build up from any joint connection. This condition can easily be remedied by removing and cleaning both joint pieces and reassembling with high temp silicone and torquing the exhaust clamp to the proper spec. Coughing is usually caused by an air leak in the intake system and will generally have the same telltale signs of location by a wet or damp buildup of oil/gas seepage at the intake manifold to cylinder head or carburetor connection and in rare instances a worn throttle plate shaft and or seals. Spitting is usually caused by a faulty accelerator pump and or nozzle, or the float bowl needle and seat leaking and overflowing through the main jet mixing well nozzle, or the air-fuel mixture screw is adjusted too lean. For more information about your issue and valuable "FREE" downloads that you need please click on the links below. Good luck and have a nice day. Star 1100 popping noise
Popping and backfiring in 02 Yamaha VStar 1100 Twin Forum Harley Davidson...
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2000/LIT-11626-13-36_96.pdf

Apr 10, 2014 | 2007 Yamaha V Star 1100 Classic

1 Answer

How to adjust carburator Jeep Wrangler 4.0 258 of 1991


While engine is turned off.Screw shut both fuel and air mixture.Then each screw turn open 2 and half turn or some times 2 full turns.that should give close enough mixture .then switch engine on and make sure idle at 10rpm for auto and 6 rpm for manual.Then adjust screws lightly to your needs constant check rear exhaust for color of smoke if black it\'s too rich in fuel and if it\'s a farting noise coming out of the exhaust it\'s too lean.The sound out of the exhaust should be running continues and no missing.

Dec 16, 2013 | Crown 1991-1993 Jeep Wrangler YJ Drive...

1 Answer

Ajust idle on 2002 FXDL


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time. Good luck.

Oct 04, 2013 | 2002 Harley Davidson FXDL Dyna Low Rider

1 Answer

Adjust air fuel mixture


Hi Wentzpatrick, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time. Good luck.

Jul 15, 2013 | Harley Davidson XLH Sportster 883...

1 Answer

How do you adjust ldle air mixture on 2002 dyna low rider


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time. Good luck.

Apr 14, 2013 | 2002 Harley Davidson FXDL Dyna Low Rider

1 Answer

How do i adjust the idle on my 03 dyna wide glide


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time. Good luck.

Aug 18, 2012 | 2003 Harley Davidson FXDWG Dyna Wide Glide

1 Answer

1999 Road King Carb Adjustment


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time, final adjustment should be made with the engine at normal operating temperature. Good luck and hace nice day.

Apr 27, 2012 | Harley Davidson FLHR-FLHRI Road king...

1 Answer

Is a 1998 95th anniversary harley davidson softail springer have a carburator


Hi Anonymous, on the right hand side of the carburator there is an idle adjusting screw with a spring behind it, turn screw clockwise to increase idle counter clockwise to decrease idle. There is also an air/fuel mixture screw inside a carb body lug that may or may not be plugged with an aluminum cap that's about 3/16" thick. This cap can be drilled out to acess the air/fuel mixture screw. Turning screw clockwise will lean out mixture and lower idle, turning screw counter clockwise will richen mixture and raise idle. You need to balance the two adjusting screws to obtain an idle of 950-1000 RPM then back out air/fuel mixture screw 1/4 turn, snap throttle to confirm responce, you may continue to back out air/fuel mixture screw untill desired throttle responce is achieved, if you see black smoke coming out of exhaust you have gone to far and need to turn screw back in 1/8 turn at a time, final adjustment should be made with the engine at normal operating temperature. Good luck and hace nice day.

Apr 16, 2012 | 2000 Harley Davidson FXSTS Springer...

Not finding what you are looking for?
2001 Yamaha V Star 1100 Classic Logo

1,333 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

Tom

Level 2 Expert

314 Answers

vince

Level 3 Expert

1216 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1165 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...