Question about 2005 Benelli TnT

1 Answer

STALLS AND WON'T START UNTIL COOL IF RIDING IN STOP AND GO SLOW TRAFIC FOR A LONG TIME. eNGINE COOLANT LEVEL IS ON THE LOW MARK OR BELOW BUT THERE IS NO ROOM FOR ME TO ADD MORE.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 375 Answers

You say "COOLANT LEVEL IS ON THE LOW MARK OR BELOW BUT THERE IS NO ROOM FOR ME TO ADD MORE."
That doesn't make sense - if it is low, there must be room to add more.
I would bleed the whole system - you may have an air block. Pay particular attention to the water pump.

Posted on Jun 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i put water in my radiator?


you need to replace thermostat and radiator cap.look under hood around engine compartment.look for a radiator cap near radiator,add 50/50 antifreeze and water to coolant system to bring up boiling point.pure water will cause engine run hotter because water evaporate away,remove radiator pour coolant in the radiator until coolant stop dropping in the radiator now some vechicle pour coolant in the coolant overflow jug,pour coolant until coolant level stop dropping and the coolant level stay at cold full mark.start engie let idle few minutes, watch coolant level in radiator if coolant start dropping add more coolant, when coolant level stop dropping put radiator cap back on let engine idle until both top radaitor hose and bottom coolant hose get warm turn off engine wait until it get cool then take a large rag slightly open radiator just a litle at a time to keep from getting scaled.once radiator remove add more coolant if low,put radiator cap back on start the engine let it idle watch the temp gauge if temperature gauge going hot zone stop engine wait until cool then add more coolant,keep doing this until engine stop overheating going into hot zone and coolant level stop dropping,make the coolant overflow jug coolant level stay at full cold mark, dont let jug run empty if so air will get in the coolant system causing engine to overheat.

Jul 22, 2012 | 2000 Plymouth Breeze

1 Answer

No my alero is overheating. I have replaced the thermostat and waterpump and put a new cap on reservior and im losing coolant out the overflow


YOU NEED BLEED AIR OUT THE COOLING SYSTEM.WAIT TO ENGINE COOL DOWN.YOUR VECHICLE YOU HAVE TO POUR COOLANT IN THE COOLANT OVERFLOW JUG UNTIL COOLANT LEVEL STAY AT THE FULL COLD MARK.THEN START ENGINE LET IT IDLE A FEW MINUTES WATCH COOLANT IN THE OVERFLOW JUG WHEN IT DROPS ADD MORE COOLANT UNTIL COOLANT LEVEL STAY AT FULL COLD MARK.WHEN COOLANT LEVEL STOP DROPPING IN OVERFLOW JUG.SCREW RADIATOR CAP BACK ON OVERFLOW JUG WATCH ENGINE COOLANT TEMPERATURE GAUGE AS COOLANT TEMPERATURE START CLIMBING TURN OFF ENGINE LET IT SET A WHILE KEEP FROM GETTING SCALDED.TAKE LARGE RAG PLACE OVER COOLANT OVERFLOW JUG CAP SLOWLY OPEN RADIATOR CAP A LITTLE AT A TIME UNTIL PRESSURE RELEASE.REMOVE OVER FLOW JUG CAP.ADD MORE COOLANT UNTIL COOLANT LEVEL AT THE FUL COLD MARK ON THE OVERFLOW JUG.THEN SCREW CAP BACK ON THE OVERFLOW JUG.START ENGINE LET IT IDLE AGAIN WATCH ENGINE COOLANT TEMPERATURE GAUGE WHEN TEMPERATURE GAUGE START CLIMBING.TURN OFF ENGINE WAIT A WHILE.CHECK COOLANT LEVEL IN THE OVER FLOW JUG.DO THIS PROCEDURE UNTIL THE COOLANT LEVEL IN THE COOLANT OVERFLOW JUG STOP DROPPING AND STAY AT FULL COLD MARK,WHEN THE TOP RADIATOR HOSE GET HOT THERMOSTAT OPENING AIR IS OUT THE COOLANT SYSTEM. WHEN ENGINE COOLS DOWN.CHECK COOLANT OVERFLOW JUG COOLANT MUST BE IN THE COOLANT OVER FLOW JUG AT THE FULL COLD MARK WHEN ENGINE COLD. DONT .DONT OVERFILL COOLANT OVERFLOW JUG.KEEP COOLANT IN THE OVERFLOW JUG IF YOU LET COOLANT OVERFLOW JUG RUN DRY AIR WILL BE DRAW IN COOLANT SYSTEM CAUSE ENGINE TO OVERHEAT.

Aug 12, 2011 | 1999 Oldsmobile Alero

3 Answers

I replaced my radiator on my 2004 with a 2.2 and it seems like the thermostat is not opening. It can not get the air out. It seem to just to over heat and push the coolant out. Randy


REPLACE THERMOSTAT IF TOP COOLANT COOLANT HOSE GOING TO RADIATOR IS HOT TO TOUCH THERMOSTAT OPEN. TO BLEED COOLANT SYSTEM FIRST YOU NEED TO ADD COOLANT TO THE COOLANT OVER FLOW JUG UNTIL COOLANT LEVEL STOP DROPPING AND STAY AT FULL COLD MARK.WAIT 3 MINUTES IF COOLANT DROPS ADD MORE COOLANT UNTIL COOLANT STAY AT FULL COLD MARK.WITH RADIATOR OVER CAP OFF CRANK ENGINE FOR MINUTE WATCH COOLANT LEVEL AT OVERFLOW JUG.IF COOLANT DROPS ADD MORE COOLANT IN THE OVERFLOW JUG.WHEN COOLANT LEVEL STOP DROPPING IN OVERFLOW JUG.SCREW BACK ON THE RADIATOR CAP TO OVERFLOW JUG.WHILE ENGINE IDLING WATCH TEMPERATURE GAUGE WHEN TEMPERATURE START CLIMBING TURN OFF ENGINE WAIT A WHILE KEEP FROM GETTING SCALDED.WHEN COOLANT COOL DOWN SOME. PLACE A LARGE RAG OVER THE COOLANT OVERFLOW JUG OPEN CAP LITTLE AT A TIME UNTIL PRESSURE RELEASED, THEN REMOVE CAP ADD MORE COOLANT IN THE OVERFLOW JUG TO THE FULL COLD MARK.THEN REPEAT THE PROCESS SCREW BACK ON THE COOLANT OVERFLOW RADIATOR PRESSURE CAP.THEN START ENGINE WATCH TEMPERATURE GAUGE WATCH COOLANT TEMPERATURE GAUGE WHEN COOLANT TEMPERATURE START RISING TURN OFF ENGINE AGAIN WAIT UNTIL ENGINE COOL DOWN ENOUGH TO KEEP FROM GETTING SCALDED TAKE PLACE LARGE RAG OVER RADIATOR CAP WHICH IS THE COOLANT OVERFLOW JUG CAP OPEN CAP LITTLE AT A TIME UNTIL PRESSURE RELEASED ADD COOLANT UNTIL AT FULL COLD MARK. WHEN YOUR COOLANT LEVEL STOP DROPPING.AND TOP RADIATOR HOSE VERY HOT THERMOSTAT OPEN AND AIR IS OUT THE COOLANT SYSTEM. MAKE SURE YOUR COOLANT OVERFLOW JUG HAS COOLANT IN IT,WHEN ENGINE COOL DOWN CHECK COOLANT OVERFLOW JUG KEEP COOLANT LEVEL AT FULL COLD MARK.BECAUSE IF OVERFLOW JUG IS EMPTY THATS A SIGN RADIATOR COOLANT LEVEL LOW.WHEN OVERFLOW JUG EMPTY IT WILL ALLOW AIR GET IN THE COOLANT SYSTEM AND CAUSE CAR TO OVERHEAT.WHEN REPLACING THERMOSTAT ALSO REPLACE THE RADIATOR CAP ON THE COOLANT OVERFLOW JUG.

Aug 09, 2011 | 2004 Oldsmobile Alero

1 Answer

Need to know if i need to bleed the cooling system, after installing the radiator?


ADD COOLANT IN THE COOLANT OVERFLOW JUG UNTIL COOLANT LEVEL STOP DROPPING AND COOLANT LEVEL STAY AT THE FULL COLD MARK.PLACE COOLANT OVERFLOW JUG CAP BACK ON JUG.CRANK VECHICLE UNTIL ENGINE START WARMING UP. STOP ENGINE WAIT FOR A WHILE UNTIL COOLANT COOL DOWN TO KEEP FROM GETTING SCALDED. USE A LARGE RAG OVER THE OVERFLOW JUG CAP OPEN OVERFLOW JUG CAP A LITTLE AT A TIME REMOVE OVERJUG CAP CHECK COOLANT LEVEL ADD MORE. COOLANT IN THE OVERFLOW JUG.THEN START VECHICLE AGAIN.LET ENGINE IDLE UNTIL TOP RADIATOR GET HOT.THEN THERMOSTAT WILL BE OPEN.WHILE ENGINE IDLING WATCH THE TEMPERATURE GAUGE IN VECHICLE IF TEMPERATURE GAUGE START CLIMBING IN THE HOT ZONE.TURN OFF VECHICLE LET IT SET A WHILE THEN USE LARGE RAG REMOVE OVERFLOW JUG CAP.ADD MORE COOLANT, PLACE CAP BACK ON START VECHICLE AGAIN KEEP DOING THIS PROCEDURE UNTIL TEMPERATURE STOP CLIMBING HOT ZONE.AND WHEN COOLANT LEVEL STOP DROPPING IN THE COOLANT OVERFLOW JUG.AIR IS OUT THE SYSTEM, BUT KEEP COOLANT LEVEL IN THE COOLANT OVERFLOW JUG AT THE FULL COLD MARK.DONT OVERFILL.DONT LET COOLANT OVERFLOW JUG RUN DRY IF SO AIR WILL ENTER COOLANT SYSTEM BECAUSE COOLANT LEVEL WILL BE LOW ENGINE WILL START OVERHEATING.

Jul 24, 2011 | 2006 Dodge Grand Caravan

2 Answers

My sunfire overheats and leaks out overflow everytime i drivee it.i changed water pump,thermostat the fan is working fine and had a water pressure test done last mth


DID YOU BLEED AIR OUT THE COOLANT SYSTEM.TO BLEED COOLANT SYSTEM, FILL THE COOLANT SYSTEM THROUGH THE RESERVOIR TANK OR THE RADIATOR UNTIL THE FULL COLD MARK IS REACHED.BESURE TO USE 50/50 HALF WATER AND ANTIFREEZE.YOU CAN BUY ANTIFREEZE THAT IS ALREADY PREMIX 50/50.AFTER ADDING ANTIFREEZE TO RESERVOIR OR RADIATOR FILL RADIATOR TO FULL MARK OR IF YOU DONT HAVE RADIATOR CAP ON RADIATOR POUR ANTIFREEZE IN THE OVERFLOW JUG UNTIL COOLANT LEVEL STAY THE FULL COLD MARK.WAIT AWHILE UNTIL COOLANT LEVEL STOP DROPPING.NOW INSTALL THE RADIATOR OR OVER FLOW JUG CAP.START THE ENGINE AND ALLOW IT TO RUN UNTIL NORMAL OPERATING TEMPERATURE IS REACHED AND THE UPPER RADIATOR HOSE BECOME HOT.STOP THE ENGINE AND OBSERVE THE COOLANT LEVEL IN THE OVERFLOW JUG. THE COOLANT LEVEL SHOULD BE AT THE FULL HOT LINE.ALLOW THE ENGINE TO COOL UNTIL THE AMBIENT TEMPERATURE IS REACHED THEN CHECK THE COOLANT LEVEL IT SHOULD BE AT OR ABOVE THE FULL COLD LINE.ADD MORE COOLANT IF NECESSARY. WARNING BECAREFUL WHEN OPEN THE RADIATOR CAP OR JUG OVER FLOW CAP.USE A LARGE RAG OVER THE RADIATOR CAP TO KEEP FROM GETTING SCALDED.OPEN RADIATOR CAP A LITTLE AT A TIME TO KEEP FROM GETTING SCALDED.WAIT UNTIL ENGINE COOL DOWN BEFORE OPENING RADIATOR CAP OR OVERFLOW JUG CAP.WEAR SAFETY GLASSES.

Jul 12, 2011 | Pontiac Sunfire Cars & Trucks

2 Answers

The radiator was emptied out and i want to add antifreeze and water? there are 2 areas that say antifreeze goes here?


  • One is the radiator and the other is an overflow tank. Sometimes anti freeze will back pressure a bit and need somewhere to go and other times the antifreeze gets low in the radiator. That is the purpose of the radiator.
  • Put the antifreeze in the radiator fist and then add to the reservoir. Pay attention to the cold/hot level fill on the overfill tank.
  • You need to find out where all that antifreeze went to if the radiator was empth. Pull the dipstick and look for a chocolate milk look on the oil. This would be a head gasket or a cracked head.
  • Otherwise keep an eye out for a leak and repair it soon.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jun 15, 2011 | Ford F-250 Cars & Trucks

2 Answers

My temp gauge goes to the third line before fans come on and only the low fan comes on. I already replaced thermostat, engine coolant temp. sensor and radiator flush... any idea why high fans dont come on...


CHECK COOLANT FAN FUSES AND RELAYS. CHECK COOLANT LEVEL.MAKE SURE ITS NOT TOO LOW BECAUSE IF COOLANT TOO LOW . BY NO COOLANT AROUND OR COOLANT SENSOR NOT SUBMERGED IN COOLANT COOLING FANS WONT TURN ON.MAKE SURE YOU HAVE 50/50 ANTIFREEZE AND WATER. CHECK FOR CLAPSE RADIATOR HOSES.CHECK RADIATOR HOSE AT WATER PUMP.IF HOSE LOOK CLAPSE REPLACE IT AND BLEED COOLANT SYSTEM.IF EVERY THING HAS BEEN DONE YOU NEED ENGINE BLOCK FLUSHED OUT.HEATER CORE ALSO COULD BE STOPPED UP.A VERY HIGH MILEAGE ENGINE WILL OVER HEAT.OLD ENGINE LOSES COMPRESSION AND HORSE POWER.PUTTING MORE LOAD ON THE OLD ENGINE WILL MAKE IT OVER HEAT.IF COOLANT LEVEL IS LOW.BLEED COOLANT SYSTEM.START THE ENGINE LET IT IDLE FEW MINUTES WATCH THE COOLANT TEMPERATURE GAUGE.WHEN TEMPERATURE START RISING.TURN OFF THE ENGINE LET IT SET FOR 20 MINUTES.TAKE A LARGE RAG PLACE OVER RADIATOR CAP ON COOLANT EXPANSION TANK SLOWLY OPEN RADIATOR CAP JUST A LITTLE TO RELEASE A LITTLE PRESSURE AT A TIME.DONT OPEN CAP RAPIDLY OR YOU WILL GET SCALDED.ONCE THE RADIATOR CAP REMOVED.IF COOLANT LOW ADD MORE COOLANT IN THE THE COOLANT EXPANSION UNTIL YOU GET TO THE COLD MARK.REPEAT THIS PROCEDURE START ENGINE LET IT RUN UNTIL TEMP GAUGE START CLIMBING A BIT DONT LET CAR RUN TO OVER HEAT JUST IDLE UNTIL TEMP JUST START TO RISE.THEN YOU TURN OFF ENGINE. WAIT 20 MINUTES.THEN USE LARGE RAG OPEN RADIATOR CAP LITTLE AT A TIME. DO THIS PROCEDURE UNTIL THE COOLANT IN THE EXPANSION TANK STOP DROPPING. THEN ALL THE AIR IS BLEED OUT THE COOLANT.WHEN COOLANT LEVEL STOP DROPPING, WHEN YOU DRIVE CAR AROUND.AND TURN OFF ENGINE.WHEN ENGINE OFF CAR SET FOR A WHILE KEEP CHECK ON THE COOLANT LEVEL IN COOLANT EXPANSION TANK. THE COOLANT LEVEL SHOULD BE AT THE COLD MARK IN THE EXPANSION TANK.MAKE SURE COOLANT IS IN THE EXPANSION TANK.IF NOT AIR WILL DRAW IN COOLANT SYSTEM. CAUSING ENGINE TO OVER HEAT.IF BLEEDING AIR OUT THE COOLANT SYSTEM DONT HELP AND COOLANT FANS DONT TURN ON YOU HAVE PCM PROBLEMS.

Apr 22, 2011 | 2004 Pontiac Grand Prix

2 Answers

Having issues with a 2000 chevy impala overheating have changed the radiator and the thermostat fans seem to be working ok but overheats at idle in stop and go traffic, after a certain amount of time it...


YOU NEED BLEED COOLANT SYSTEM.CHECK COOLANT LEVEL IN RADIATOR.ADD MORE DEXCOOL UNTIL COOLANT LEVEL IS CLOSE TO RADIATOR SPOUT.CRANK ENGINE LET IDLE UNTIL TOP RADIATOR HOSE GET HOT.WATCH TEMPERATURE GAUGE.IF TEMPERATURE GAUGE START RISING TO HOT ZONE.TURN OFF ENGINE.LET COOL DOWN.USE LARGE RAG SLOWLY OPEN RADIATOR CAP A LITTLE AT A TIME UNTIL ALL PRESSURE RELIEVED.REMOVE RADIATOR CAP.ADD MORE COOLANT.CRANK CAR AGAIN LET IDLE UNTIL TOP RADIATOR GET HOT.KEEP EYE ON TEMP.GAUGE ALSO.WHEN TEMP.GAUGE STOP CLIMBING.YOUR COOLANT SYSTEM BLED.WHEN DONE LET CAR SET A WHILE CHECK COOLANT LEVEL.ALSO FIRST THING IN THE MORNING CHECK COOLANT LEVEL AGAIN.AND BESURE ADD COOLANT IN THE OVERFLOW JUG TO THE COLD MARK.DONT OVER FILL THE COOLANT RESERVOIR JUG.WORK SAFELY DONT GET SCALDED.

Feb 15, 2011 | 2000 Chevrolet Impala

1 Answer

CAR RUNNING HOT AFTER I CHANGED A BAD RADIATIOR OK RADIATIOR HAD A WHOLE IN IT WE CHANCED IT BUT NOW ITS RUNNING HOT HOW DO I PROPERLY REFILL THE RADIATIOR


CHECK COOLANT LEVEL STILL LOW.ADD MORE COOLANT.UNTIL RADIATOR OVERFLOW FULL AT COLD MARK.THEN CRANK ENGINE UP LET IDLE FEW MINUTES LOOK DOWN COOLANT OVER FLOW JUG ADD MORE COOLANT IF LEVEL DROPPED.WHILE ENGINE RUNNING KEEP EYE ON TEMPERATURE GAUGE.WHEN THERMOSTAT HOSE GET HOT.TURN OFF ENGINE WAIT A LITTLE WHILE TO KEEP FROM GETTING SCALD TAKE LARGE RAG PLACE OVER OVERFLOW JUG RADIATOR CAP.OPEN CAP A LITTLE A TIME.IF COOLANT TRIES BOIL OUT.LET VECHICLE SET A WHILE LONGER.ADD MORE COOLANT.WHEN COOLANT LEVEL CORRECT AND ALL AIR OUT THE COOLANT SYSTEM.IT WILL STOP OVERHEATING.LONG AS ENGINE RUNNING HOT TURN OFF THE ENGINE POUR IN MORE COOLANT UNTIL COOLANT LEVEL STOP DROPPING IN RADIATOR.KEEP COOLANT LEVEL IN OVERFLOW AT COLD MARK.DONT OVER FILL OVERFLOW JUG.

Jan 23, 2011 | 1996 Lincoln Continental

2 Answers

Heat is not working - coolant was low so filled it.... problem here... heard something about an air pocket


If you dont have an external coolant leak anywhere under your hood that has shown up on your driveway it could be the intake manifold or the headgasket leaking. Also check the thermostate to solve the heat issue.

Jan 05, 2011 | 1998 Pontiac Bonneville

Not finding what you are looking for?
2005 Benelli TnT Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Benelli Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Frank Richardson

Level 1 Expert

19 Answers

Jim

Level 3 Expert

831 Answers

Are you a Benelli Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...