Question about 1996 kawasaki ZX-7R

1 Answer

Just fitted s/steel motad headers and now theres

Just fitted s/steel motad headers and now theres a flat spot in 4,5,6 gear at 5-6000rpm, is this usual?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 948 Answers

It is not at all unusual for an exhaust change to change the torque characteristics of the motor. That's the whole reason for putting on a new exhaust (unless you just want to make more noise.) Have you examined dynamometer runs from your engine showing the stock output vs. the s/steel motad headers output? How do the two compare? Have you changed carburation at all?

Posted on Jun 28, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I install headers on a 70 Chevelle SS Do I need to raise the engine ?

Depends on your setup, engine and the headers you purchased. Some headers will not fit in a car body at all. Make sure you have a header that is made to fit your engine and chassis. Most headers on cars are a tight fit but most issues are with the steering column not the frame.

Feb 17, 2015 | Pacesetter Armor Coat Ceramic Header 97-01...

1 Answer

How Can I replace A Blown Fan header On my Mother Board. It's weird The three pin fan does not work in the three pin spot but when I ug it into the 4 pin header it works. The 4 pin fan does not work on...

If you have to ask about the difficulty, then you probably lack the skill to do the job. The 4 pin fan header is usually for the CPU fan and the 3 pin one is usually for case cooling. The extra pin is for speed control of the CPU fan (to cut noise) If the 4 pin fab fails on the 4 pin header then the fan has probably failed, because the 3 pin one works.

Apr 17, 2013 | Computers & Internet

1 Answer

I have a 2006 pacifica misfiring in cylinder 4. How do i locate that one

Go to the auto parts store and get a tester that fits on the spark plug and on the spark plug coil and it will flash if the plug is firing.You could use a inferred thermometer and aim at the exhaust header and the cold spot is the cylinder not firing. Number 4 is the cylinder in the middle by the radiator side

Mar 24, 2013 | 2004 Chrysler Pacifica

1 Answer

Suzuki gs 500 e rejetting

ok found this hope it helps... link

Feb 26, 2013 | Motorcycles

2 Answers


I have had this issue before. The problem is that you don't have enough back pressure. which is basically how much pressure it takes for the exhaust to exit the pipe. what you would need to do is add baffling the plates and tubes in the end of the pipe to add back pressure.

Mar 16, 2012 | 2001 Honda Deauville NTV 650

1 Answer

Flat spot when excellerating in 1st gear between

good day just ask the qualified honda tech. to fix your problem.

Jun 21, 2010 | 2000 Honda VFR 800

1 Answer

Brought a motad exhaust for a honda deuaville 650 the center stand bracket will not fit any ideas as there are no drilled holes on the system it's self

the bracket fits on the left hand side of the bike- contact us at the factory and we will talk you through it

Motad UK

Mar 01, 2010 | 2000 Honda Deauville NTV 650

1 Answer

Case front firewire port to motherboard connection???

Yeh dont plug it into a USB header...

yes if you buy a PCI firewire card they will have 1 or 2 headers on the card so you can fit your front Firewire port to it...
[Belkin cards 99% of the time have headers on the card]

Let me know...

Jan 22, 2009 | ASUS P4S533-VM (P4S533-VM/L) Motherboard

Not finding what you are looking for?
1996 kawasaki ZX-7R Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4988 Answers


Level 3 Expert

80417 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides