Question about 2001 Honda CBR 600 F(4)i Rossi

1 Answer

Fuel pump not coming on.

I took the body, and tank off to get painted. I put the tank back on, I cannot hear the fuel pump. Any ideas?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 408 Answers

Have you connected back the pump properly? Does the pump relay engages as it should?This will happen when you turn the key while the kill switch is at "run" position.

Posted on Jun 28, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you know if the fuel pump is bad

if you remove the fuel cap from the fuel tank put your ear to the tank holehave someone turn the key to the start position or to the run position and if you don't hear the fuel pump buzzing at that turned it is possible that you either have a problem with the fuel pump for the fuel pump wiringsometimes it can even be a bad ground for the fuel pump which is usually somewhere on the fuel tank for the body of the vehicle

May 15, 2014 | Cars & Trucks

1 Answer

I have a 2001 Mazda protege. Has new fuel pump and pressure regulator, I have cleaned fuel tank , lines, rail, and injectors. Relays and fuses are good. I took breather off and sprayed fuel into throttle...

sounds like an electrical problem .pump isnt coming on .turn on key listen for fuel pump to come on for 10 seconds then shut off on its own. If you dont hear the pump then its probley fuel relay . next check wires are plugged into fuel pump. lots of cleaning ?? is the fuel rail screen plugged ???? disconnect before rail if the pump comes on next. turn on key check for fuel pumping out line .

Nov 21, 2013 | Cars & Trucks

1 Answer

New fuel pump but no fuel

Check the fuel pressure regulator at the fuel rail or throttle body.

Feb 11, 2013 | 1993 Dodge Dakota

3 Answers

1982 Chevy K10 Fuel Problems

Check to see if timing belt is broken. or wiring to crank-shaft sensor and check sensor itself on front of flywheel typically but may be on side of block usually the further towards the transmission is Crank and closer to front is cam sensor.

Check relays by switching from others of the same numbers.
Crank-shaft positioning sensor is bad perhaps.
Remove plug under vehicle that leads to fuel pump and check for voltage when key is turned on. if voltage is there is either defective fuel pump, was put in wrong or is harness from that point to the pump.
try banging the tank with hammer as someone turns key on.
 check harness from fuel pump to where it goes into the body - remove from body plug and inspect.
Should be either and or both a fuel pump relay and fuse! 
Run 12 volts to the positive side of the fuel pump wiring to see if pump is good. 3 wires usuallly  1 is ground for both the fuel guage and the other positive for the pump. and other is positive for the fuel pump guage and these two wires for the guage will show some resistance. put a fuse inline with the 12volts to the fuel pump positive but cut the line to the body prior to this - temporarily.
Could be bad switch in ignition unit in steering column but doubtful.

Hope this helps.

Jun 09, 2010 | 1983 Chevrolet K1500

1 Answer

My 1993 GMC 1/2 ton truck stopped suddenly and will not start.

The inline will not work,it can not get fuel threw the fuel pump in the tank,the fuel tank has to be removed,and the fuel pump changed out.

Apr 12, 2010 | 1989 Chevrolet K1500

2 Answers

How to remove fuel pump 1995 camaro z28 5.7

If you have a Fuel pump blown and needs replacing you probably have been quoted approx $220 for the pump and about $450 labour and about 6 hours of work.
Due to its location you would have been informed that suspension, exhaust, support bars etc have to be removed before the tank is removed then the pump removed right?
Here's what I did, I removed the back carpet, I then drew a cut out area central on the flat of the highest point on the body pannel and cut a wide hole, leaving one section attached for folding back down later. My position was perfect, I unscrewed the pump and replaced it with the new unit.
I cut the plate with a drill to start, then I used tin snips to complete the cuts. {NO GRINDER or OXY}
I folded down the flap and sealed it, I then got 2 galv plates from home depot {$0.80 each} and screwed it over the top, then sealed the edge and sprayed it with a can of black paint. Looks like a factory access area.
Took me 55 minutes all up, and saved me $450. I have pics available

Nov 29, 2009 | Dacor Epicure ERD30 Dual Fuel (Electric...

4 Answers


The fuel pump is located on top and inside the fuel tank. A failing fuel pump sometimes will just fail and the vehicle will not run. Other times it will be weak and the vehicle will be hard to start or stall. First thing to do is replace the fuel filter. A fuel pressure test will verify if the pump is failing or failed.

Sep 25, 2009 | 1996 Dodge Intrepid

4 Answers

How to replace a fuel pump on jeep wrangler (95)

i'm pretty sure jeep had their pumps in the tank. you can phone parts place to double check. If it is in the tank, you will have to drop the tank in order to access it. Other vehicles have a latch or door thing that will allow you access from the top. pretty sure the jeep does not have this. you will have to disconnect all of the hoses and hopefully your tank is almost empty or else they weigh a ton.....then just take out the old sending unit, put on a new fuel pump and put it back...simplified version, but it will give you a gerneral idea. when i first dropped mine, it took me 1/2 a day, now i can do it in about 1.5-2 hrs

Jul 23, 2009 | 1995 Jeep Wrangler

1 Answer

1987 IROC, Ran out of gas,put gas in, now service engine light on

if you have high milieage you may have sucked in the gunk on the botton of your tank when you ran out of fuel check if you can hear the fuel pump running for about 2 sec with key on engine off if you hear nothing the problem is with your pump as they will burn out if they run dry for too long,if you hear the pump check for fuel pressure if pressure low check fuel filter to see if clogged by gunk from bottom of tank.

Mar 02, 2009 | 1987 Chevrolet Camaro

Not finding what you are looking for?
2001 Honda CBR 600 F(4)i Rossi Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4988 Answers


Level 3 Expert

80417 Answers


Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides