Question about 2002 TM Racing E 125

1 Answer

I have put brake fluid into the coolant system on my peugeot jetforce 125, is t fixable

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 375 Answers

Yes, just drain out all the coolant, replace it with fresh water and 500ml of antifreeze.
The easiest place to drain it is at the lowest point - the connection to the water pump on the side of the engine. Fill it using the radiator cap. Make sure that you don't have any airlocks when you refill - put the antifreeze in first, top up with water, leave the radiator cap off and run the bike (idle) - after a while the water level should have gone down as the water has worked it's way round the cooling system - don't worry if water bubbles over - just keep topping it up. Do this till the temp guage reads normal. Close the radiator cap and go for a short and gentle ride - don't thrash it. Check the water level again and top up as necessary. Just keep an eye on it over the next week - make sure the temp stays in the normal range - if it goes high, stop immediately and check the water.

Posted on Jun 28, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Peugeot Jetforce 50 no spark.


Hi, Steve and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. Faulty ignition coil or electronic control module.
7. Faulty pulse coil.
8. Faulty CKP, CMP, or BAS sensor.
9. Faulty ignition switch.
10. Tilt sensor needs a reset.
11. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Peugeot jet force 50cc No spark
Peugeot Speedfight fix part 7 no spark Cdi unit chat review mark savage
https://scootergrisen.dk/scooterhjemmeside/download/peugeot_jetforce_servicemanual.pdf
Peugeot JET FORCE 50 cc 2003 Parts
PEUGEOT JETForce Technical Training Manual

Aug 24, 2017 | Peugeot Motorcycles

1 Answer

Have a Peugeot Jet Force 125 and it turns over but no spark in plugs


Hi, Don and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. Faulty ignition coil or electronic control module.
7. Faulty CKP, CMP, or BAS sensor.
8. Faulty ignition switch.
9. Tilt sensor needs a reset.
10. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Peugeot jet force 50cc No spark
GY6 Electrical Troubleshooting Tutorial No Spark Eliminator
https://scootergrisen.dk/scooterhjemmeside/download/peugeot_jetforce_servicemanual.pdf
Peugeot JET FORCE 125 cc 2003 Parts
PEUGEOT JETForce Technical Training Manual

May 21, 2017 | Peugeot Motorcycles

1 Answer

My 125 Satelis ran well and suddenly stopped and will not fire


Hi, John and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Severely discharged or damaged battery, you need 12.5 volts or better and be able to pass a load test if necessary.
8. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
9. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and module.
10.. Spark plug cables in bad condition and shorting, cable connections loose, or connected to the wrong cylinders.
11. Ignition timing incorrect due to a faulty ignition coil, ignition module or sensors (MAP, CMP, CKP, O2, TPS, ETP, IAC,or BAS).
12. Faulty neutral, clutch lever, or kickstand safety switch.
13. Faulty fuel pump fuse or relay.
14. Tilt sensor needs a reset.
15. Security system not disarming alarm needs a reset.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
peugeot satelis executive 125
http://url4short.info/eb5d627f
http://e-motion.lt/wp-content/uploads/2010/01/Peugeot-JetForce-injection-Manual.pdf
PEUGEOT SATELIS 125 Spares Parts Accessories
PEUGEOT Satelis Owner Manual

Apr 24, 2016 | Motorcycles

1 Answer

Carburetor cleaning


check air filter . remove filter run scooter see if that fixes problem . if it does buy new air filter

Jul 14, 2013 | 2007 Peugeot JetForce 125 ABSPBS

1 Answer

My peugeot jetforce 50cc bike just stopped in traffic now it turns over but wont run has plenty of petrol


I'm guessing this is a 2 cycle engine ? , if so and you are using cheap unleaded gas it contains to much water " BIO Fuel" for you engine to run properly. drain the gas and try super unleaded and see if it will start. If you are lucky for it to start you need to start using a high octane gas with aditive to elemate the water content, soon bio fuel will kill your 2 cycle engine, you need to see if you can find the no bio fuel in your area...sorry I know with will probably hard to find, thanks to our Goverment

Mar 20, 2013 | RTO Gas Motor Scooter

1 Answer

The Electrics keep cutting out. Need help.


are your battery terminals all tight , i.e the negative and positive terminal screws ?

Nov 26, 2012 | Peugeot Motorcycles

1 Answer

Peugeot 125 jetforce scooter 2003


aside from your air filter bein spotless and running the best possible tranny oil u need to take your carb off and clean out the jets, slide, float needle and the cylinder it slide up n down in, and the float bowl. also clean out the air boot and air box. if needed, a simple $115 self done top end job might be nececary, remember u have a 125 2 stroke, the most simplest of all man made machines, take advantage of such simplicity my man good luck

Feb 02, 2009 | 2002 TM Racing E 125

3 Answers

Improve speed


which i need to make faster. I have been looking at the peugeot jetforce moped which has a supercharger would it be possible to put a supercharger on mine?no chance....not unless its built for one....get better parts the supercharger wont do you any good. get a better exaughst,chain,gears,etc,,,

Nov 10, 2008 | 2003 Hyosung GV 125 Aquila

1 Answer

Winter storage


what to do with fluids?If your brake fluid is in need of changing do so before long-term storage. Similarly hydraulic clutch fluid should be changed before you store your bike; both systems may suffer failure if moisture gets in. Also make sure your coolant is fresh, as deposits can form from old fluid. For service intervals, consult your owner's manual.,,,

Nov 10, 2008 | 2006 Cagiva Raptor 125

Not finding what you are looking for?
2002 TM Racing E 125 Logo

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top TM Racing Experts

AZBen
AZBen

Level 2 Expert

193 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

JOHN LAPIER

Level 3 Expert

2428 Answers

Are you a TM Racing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...