Question about 2008 Yamaha YZF-R125

2 Answers

Raptor 350, gears slip at full throttle. Is there an adjustment

2005 raptor 350, all gears slip at full throttle. Is there an adjustment I can make ?

Posted by on

  • bartsutherin Jun 29, 2009

    Thanks for the advise! It was infact a clutch cable that was too tight. Now it works great.



    Thanks Again for the help

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 52 Answers

Sounds like you need a new clutch. but first make sure that your clutch cable is'nt too tight. it should have a little bit of freeplay when you pull the lever.

Posted on Jun 28, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 2 Answers

Clutch cable too tight ....loosen it and try again

Posted on Dec 04, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Yamaha raptor 350 makes a ticking noise once I move it down from nutral


2007 raptor 350 ticking? - Yamaha Raptor Forum

www.raptorforum.com/...raptor-350.../23854-2007-raptor-350-ticking.h...
Nov 30, 2007 - if its 100% stock then no there shouldent be any ticking, if its only 4 days old take ... as i got it up to crusing speed for a few minutes.. you'll get used to itsnoises. ... eng temp, rpm, custom one off intake, polished engine covers,. Ticking Noise - Yamaha Raptor Forum
Aug 5, 2014
2008 Yamaha Raptor 350 making grinding noise . . . - Yamaha ...
Sep 13, 2011
How To Avoid Hot Cam Ticking? - Yamaha Raptor Forum
Jan 30, 2011
raptor 350 knocking???? - Yamaha Raptor Forum
Mar 6, 2010
More results from www.raptorforum.com

Aug 01, 2015 | Yamaha Motorcycles

1 Answer

Yamaha royal star motorcycle cluch whine and shudder in 4th and 5th gear at any speed


It is slipping. These big yamahas normally have slipping clutches. Mine slips, I've just learned to baby the clutch. Make sure you are in the most comfortable gear for the speed you are running at. Avoid rolling on full power at low speeds in higher gears. It's the nature of these great beasts. Clutch springs are too weak in these bikes, you may consider an aftermarket clutch spring assembly. The "shudder"(intermittent slipping) is caused by glazing. Make sure you are using the right lubricants for your bike, some synthetics can cause problems.

1)Adjust clutch cable correctly, check
2)Pull the clutch assembly apart, if there is little wear then you have "glazed" plates, clean each plate with 600 grit sandpaper and reassemble...get a new clutch spring assembly (weakened spring causes "shudder", slippage, and consequently glazing). Reassemble and adjust correctly (many forums out there with info).
3)Replace the full assembly and adjust correctly at setup. Adjust regularly....I check adjustment about every 300-500 miles.
4)Pay a shop to do these things for you.

Oct 06, 2014 | 2005 Yamaha Royal Star Venture

2 Answers

Raptor 350 wont idle without choke on


you have debris in your main and/or idle jets or/and a plugged emulsion tube

Aug 29, 2014 | Yamaha 2005 Raptor 350

1 Answer

MyYamaha raptor 350 won't go into gear


Its more than likely the "DRIVE SELECT LEVER" (fwd to rev) on the right hand side. Apparently This is a bad design, and I am seeing this quite a bit. Try adjusting the linkage and see if that helps.

Mar 15, 2014 | Yamaha Raptor 350 ATVs

2 Answers

2001 raptor 660 won't idle, only runs with choke on, an won't take throttle???


need your carb rebuilt or your carb readjusted. sounds like you might have some mud in it. do you take it in the mud? if so check the top where the throttle cable comes through.

Sep 22, 2012 | K and N Filters Powerlid 2001-2005 Yamaha...

2 Answers

1994 nissan altima sometimes sluggish at take off, high rpms when changing gears


This sounds like a slipping transmission , check the fluid level first and make sure its full, if its full then you have ****** problems and may need to have ****** rebuild done,

Another thing is to make sure the trans passing gear cable is connected at the throttle where the gas cable is.

Sep 03, 2012 | 1994 Nissan Altima

1 Answer

I have a turbo 350 that was rebuilt with shift kit it was running good now it is holding 1st gear too long. Is there a adjustment for this.


Yes,where the detent cable hooks up to the throttle,,push in the d shaped button,and move throttle all the way full throttle and release the throttle,this will set the shift cable .If this was at all helpful,please rate,thank you.

Jul 08, 2010 | Cars & Trucks

1 Answer

2004 yamaha raptor carb removal


they are not serviceable thats why you take it to a machine shop and they can change it and make it upgradeable

Apr 01, 2010 | 2008 Yamaha Gladiator SS

4 Answers

2001 yamaha warrior valve adjustment


hello
with the cylinder set at top dead center compression. using a feeler gauge between the tappets and the valves there should be .002-.003in clearance on the intake valves, and .006-.007in. clearance on the exhaust valves. thank you.

Mar 23, 2009 | 2003 Yamaha YZ 250

Not finding what you are looking for?
2008 Yamaha YZF-R125 Logo

Related Topics:

478 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...