Question about 2003 Harley Davidson FLHTC Electra Glide Classic

1 Answer

I need to replace the bolt on the fender that holds the seat on. The bolt has some kind of washer on the inside that keep the bolt attatched to the frame of the seat. How does this come off. Do I need to cut the bolt?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 65 Answers

Its actually a bolt retainer it just so you don't lose the bolt. you can usually cut the washer off with side cutters or something if its solid, some are, then cut the bolt off your replacing it anyway right. hope this helps

Posted on Jun 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove rear fender


To remove the rear fender, you'll have to remove the 4 or 5 bolts that attatch your fender rail to fender, to keep from scratching the paint on the fender when you remove it, loosen one of the fender rails (struts) more than the other side so you can remove fender without scratching it. Becareful with your tail light wiring when your taking the license plate mount/tail light off.

Jan 24, 2015 | 2009 Harley Davidson XL 1200C Sportster...

1 Answer

How do i remove rear fender on nightster


Secure the motorcycle upright on a suitable lift and then remove the main fuse and the seat. Lift the motorcycle just sufficiently to remove pressure on the shock absorber bolts and remove the lower ones and then lift the motorcycle higher to increase clearance between the tire and the fender.THEN unplug license plate lamp connector and the right rear lighting harness connector which has a brown band on the harness near the connector and then also unplug left rear harness connector and carefully pull both rear lighting harnesses and the license plate lamp harness through the holes in the fender and free all of the harnesses from the fender harness clips and remove rear turn signal stalk nuts from under the fender on both sides. THEN loosen and remove the front fender support screw and washer and nut and then the rear fender support screw with washer and washer and nut plates if present and remove the screw and washer attaching the rear fender brace. If necessary remove license plate lamp module harness from the upper harness clips on the left side of the inner and separate the license plate bracket from the rear fender brace. THEN remove the rear fender strut covers and the attached turn signal assemblies from the fender struts and pull the turn signal harnesses through the fender holes and struts as the strut covers are taken off. THEN put suitable materials between each fender strut and fender to protect the paint. It might be best to have someone assist and hold the fender at appropriate times. THENyou can remove the seat post with its washer and screw.

Jul 04, 2014 | 2011 Harley Davidson XL 1200N Nightster

1 Answer

Remove seat on klx140


Actually, the hook is under the front end of the seat. Just remove bolts and slide it back. You have to remover the CORRECT bolts though. They are NOT the ones that are under the rear fender. Those are for the rear fender itself. The bolt for the seat are found just under the seat on the SIDES about 2/3 of the way back. You have to take off the plastic covers on both sides of the bike to get to the bots and you'll need a ratchet AND a wrench (to hold the nut on the underside of the bolt). Once you get those off, the seat should slide back VERY easily with NO umph needed. :-)

Oct 06, 2012 | 2008 kawasaki KLX140

1 Answer

Need to replace radio antenna on a 99 isuzu rodeo


I just replaced the antenna on our 02 rodeo. No need to remove radio or anything in dash. This is how I did it.
First you will need access to back of fender, enough room for your hand. Open hood and remove 3 bolts running along top of fender, open passenger door and remove top bolt holding fender. Gently pry top of fender away from vehicle. Place object in gap to hold fender ( I used the head of a rubber mallet). Reach inside fender and disconnect old antenna, follow cable through wall into passenger compartment. Gently pull cable from behind carpet and unplug old antenna from coupler. Connect new antenna to fender ( replacement antenna I ordered was slightly smaller than opening so I had to add washer). Run new antenna cable through wall and plug into coupler. Re-attach fender
1_7_2013_12_53_34_pm.jpg

Aug 23, 2012 | 1999 Isuzu Rodeo

1 Answer

How do we replace the seat on a Kohler K-3386-0 Rialto one piece toilet? The screws/nuts holding the seat down are inside the toilet and aren't accessible. Is there a way to replace the seat without...


Kohler will try to sell you $46 anchor bolt kit 84999 & also there special tool. You should expect that for a $400 toilet.

Try this instead:
1. Use 1/8" drill bit and drill and drill around the bolt until the anchor material can be removed.
2. Carefully clean hole with 11/32 drill to remove all remaining acchor material.
3. Go local hardware store & buy a 10 - 32 3/8"X3/4" rubber expansion plug (make certain threaded part is brass & has shoulder on 1 end), a 10 - 32X1.5" Phillips bolt and couple of small fender washers fit the seat.(about $4 for 2)
4. Assemble carefully not to over tighten and crack the porcelain.

Hope it helps

Oct 06, 2010 | Kohler K-3386-0 Rialto one-piece...

2 Answers

How do I remove the drivers front fender of a 1994 Dodge Ram 2500


yes undo your battery as ans air bag has a connector on the seat and if unplugged could cause air bags to go off with battery still hooked up leat sit for five min. should be four bolts or nuts holding seat down

Sep 15, 2009 | 1998 Dodge Ram

1 Answer

Eskia cracked at bolt that holds in seat


Typical problem with Eskia. To repair: remove seat and bolts, weld new material in the crack from both sides or fill with plastic epoxy, re-drill hole and install SS fender washer on top side.

Aug 17, 2009 | Necky Boating

3 Answers

Replace front fenders 1999 wrangler


Take off the tyre and remove the plastic inner fender first.

Mar 17, 2009 | 1999 Jeep Wrangler

1 Answer

I need to know where is the sensor for the gas


at the end of the fuel rail/ driver side at left of throttle assy.if your leaning over the side of the fender on drivers side. it has two 10mm bolts holding it in and a fuel line attatched and 1 vacum line attatched. its small and its called a fuel pressure regulator. steve

Feb 18, 2009 | 1994 Lexus GS 300

Not finding what you are looking for?
2003 Harley Davidson FLHTC Electra Glide Classic Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...