Question about 2000 kawasaki VN 1500 Vulcan Classic

1 Answer

I believe my motorcylce a 2000- Vulcan 1500 has blown a fuse because I dont have any power to the bike lights or starter. Where are the fuses for this located

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I actually have a scematic of this as I have a friend with an earlier model.
The fuse box is shown above the battery but is not clear.
My friends is in a state of severe strip down, loads of wear, my advise is mend the electrics and sell it!

Posted on Jun 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 Kawasaki VN 1500 Vulcan Classic no electrical power


Hi, Electricland before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
No power when switch is turned on
http://www.kawasakimotorcycle.org/forum/kawasaki-cruisers/140240-99-vulcan-1500-classic-electrical-system-totally-dead.html
http://www.vulcansabs.com/wp-content/uploads/2016/04/Kawasaki-Vulcan-VN1500-Nomad-Classic-Tourer-1998-1999-Service-Manual.pdf
OEM Parts for Kawasaki
1998 Kawasaki Vulcan 1500 Classic Owner Manual

Apr 21, 2013 | 1998 kawasaki VN 1500 Vulcan Classic

2 Answers

Need radator for kawasaki vn 1500 classic tourer 2001 is the driffter the same radator as the vn 1500 classic plz hellllllllllllp


TO ALL VN1500 OWNERS....This once happen to me,
I went to the garage to start the bike "Nothing ""The first thing is the lights are bright but no turning over,Next you think the solenoid is kaput but the answer was very simple and the fix takes 30 seconds..
Do not take the bike to bits looking for other problems and look at the clutch leaver and you will see some wires going into a plastic shroud going into the switch in the clutch leaver, Make sure this has not popped out if its connection as it some times may do after a few years due to constant turning on the handlebars,
When this is not connected you will have a bike that will not fire up but comes alive and you will hear a clicking noise but this is from the engine carb area and every function of the bike will work but it will not turn over, Worth looking at and saves sixteen quid for a starter unit you never needed.

Feb 06, 2012 | kawasaki VN 1500 Vulcan Classic Tourer Fi...

1 Answer

No power to the starter I have got power to bike, Ing switch on ,handlebar switch on ,bike is in nutral kick stand is down ,starter fuse ok.when I push the starter button ,no power to starter


It could be the switch for the kickstand. I am more familiar with Harleys, they have a switch on the clutch which is the same as the kickstand switch on other bikes

Aug 28, 2011 | 2001 kawasaki VN 1500 Vulcan Drifter

1 Answer

2003 kawasaki 1500 fi nomad - No battery power to bike. Battery charged, no lights or displays, main fuse and and fuses in fuse box OK.


Ok, locate and check the fuse at the starter solenoide, this is the main power fuse, follow the red battery lead until you locate the solenoide, here you should find under a cover a 30 amp fuse, hope this helps , paul

Feb 27, 2011 | 2003 kawasaki VN 1500 Vulcan Classic...

1 Answer

WE HAVE A DODGE 4X4 1500 YEAR 2000 TURN


There is a service bulletin that I believe might take care of your problem.The bulletin number is 08-01-00 revision A.the problem is the starter relay fuse being blown.Check the fuse in the power distribution center.It is fuse D.If it is blown then you will have to replace the fuse and install the relay harness.Part number is 05019015AA.This is a Dodge part number and you will have to get it from the dealership.Hope this helps.Good luck.

Feb 02, 2010 | 2000 Dodge Ram 1500 Truck

1 Answer

200o 1500 vulcan classic. My ignition fuse blows


you have a short somewhere in the ignition line. check all connections at coil, check for worn spark plug cables grounding on block.

Jul 25, 2009 | 2000 kawasaki VN 1500 Vulcan Classic...

1 Answer

Starter relay fuse keeps blowing


30 amps is heavy, so bypass nothing. Look for a short in a heavy circuit like the the headligh, starter (questionable because of delay) same with starter relay. You have a wire shorting out on the frame somewhere. It's that cut and dry.. Go to the auto parts store and buy an automatic circuit breaker that matches the fuse type your bike uses. but instead of a 30 amp, get a 20 or 25 amp. As long as theres a short it will trip and reset by itself saving you the hassle of changing fuse every few minutes.. While the breaker cycles on and off you can search for the short. When you find it, the breaker will stop cycling and stop in the on or reset. Good Luck

Jun 11, 2009 | 2000 kawasaki VN 1500 Vulcan Classic...

1 Answer

Kawasaki Vulcan Classic 1500


Was any of the wires cut through?  Just a shot in the dark, but try unplugging and re-plugging the wire connector going into the clutch lever.  If that doesn't work submit more information.

Nov 08, 2008 | kawasaki Full Suspension Mountain Bike Men

Not finding what you are looking for?
2000 kawasaki VN 1500 Vulcan Classic Logo

Related Topics:

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4888 Answers

yadayada
yadayada

Level 3 Expert

79847 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...