Question about 2000 Husqvarna WR 360

1 Answer

I don't know how much transmission oil need the Husqvarna wr360, 2000. I was buy this bike but I don't know how changing oil.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 115 Answers

There is a screw on the side of the lower unit, you remove this screw, fill with proper lubricant and then hold the bike upright, it will then overflow to the proper level.

Posted on Jul 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I change seal on water pump twice and oil in gearbox is still grey???Husqvarna WR300-2012????


after you changed the seal did your water level drop If the seal is still leaking you should see a change in coolent level Also did you flush the motor with solvent if not it could take more than 3 oil changes to see a change hope this helps I currently race 2 husky 125 2 stokes off road anand i dont know of another way to get water in the oil except thruogh the overflow and that takes some serious waterplay good luck dirt bike dan

Apr 17, 2013 | 2012 Husqvarna WR 300

1 Answer

What is the oil/fuel ration for a Husqvarna model 234 e chain saw? I recently purchased the saw new, but only the instruction manual to assemble the case was enclosed. Thank you. Don


With Husqvarna two stroke oil it should be 50-1, with other manufacturers two stroke oil it is 25-1 as we do not know the quaility of other oils, always try to use Husqvarna oil.

Jul 29, 2011 | Husqvarna Garden

1 Answer

My oilpan is leaking plus i need to know where to put the tranny oil when i chang the oi


You didn't say what year and model your bike was but the oil pan has gasket on it and I don't think it's too difficult to replace provided you have a way to raise the bike off the ground safely. Go to http://www.bikebandit.com and look up your bike. You can even order the parts you need from them as well. To check or add oil to the transmission, look at the chrome end cap on the transmission. There is a plug that takes a large hex key or Allen wrench to remove. It has a dipstick on it as well. The transmission takes 20-24 ounces of oil.

Good Luck
Steve

Jul 05, 2011 | Harley Davidson Bullet Sixty 5 Motorcycles

1 Answer

Need to know how to change tranny fluid in 2002 fatboy.


Since I don't work on the later model bikes, I'm not certain when Harley changed the location of the transmission drain plug. On your model, there should be a drain plug on the bottom of the transmission. If not, it's a small pipe plug located just below the chrome end cover of the transmission behind the exhaust pipes. The difficulty in getting to the plug when it's located on the side of the transmission is one of the reasons Harley moved the drain plug to the bottom of the transmission. Drain the oil and then remove the large plug from the chrome end cap on the right side of the transmission to refill it. The plug takes a large Hex key or Allen wrench to remove it, 3/8" on the earlier models. Fill the transmission with 20-24 ounces of transmission lubricant or H-D Syn3 20W50 synthetic engine oil.

Good Luck
Steve

Jul 04, 2011 | Harley Davidson FLSTF Fat boy Motorcycles

1 Answer

Best way to change oil filter


these bikes dont have a normal oil fillter. but a gauze type fillter & dont hold that much oil anyway...so you must change oil regular...as for the filter take the gauze filter out & clean it.....

Mar 22, 2010 | 2000 Husqvarna TE 410 E

2 Answers

How much oil I have to put inside the engine??


Most 900-1000cc sport bikes require 3.8 qts depending if you are also changing the oil filter or not (which I would recommend also if you do buy the filter pay the extra few $ for the Honda oil filter wrench that comes with the filter, it makes the allot easier and also works on all Honda models as well as most other model bikes with that style oil filter...but remember only a quarter turn past hand tight or so should do the trick, you don’t need to go crazy)...If you are not changing the filter it will take a little less...most likely around 3 qts depending oh how much is trapped in the oil filter sill

Buy 4 quarts. Put 3 in and run the bike for about a min or two at idle to let the oil circulate as well as heat up and expand. Then shut the bike off and let it sit for another 5 min, then if needed have a friend hold the bike upright or do it yourself if your confident (but don’t him or sit with weight on the seat or bike or it will affect ride height and in turn oil level)

Then add oil as needed, to fill it to just under the top of the 2 oil marks (leaving a little room for the still cool oil to expand)

Then make sure everything is clean and your oil drain bolt is tight and take it for a small 5 min test ride...then check the oil again.... and you should be just where you want it

Aug 19, 2009 | 1993 Honda CBR 900 RR Fireblade

1 Answer

Bought a 2004 CBR600 RR how do i check and add oil


Oil should be changed every 2 to3K miles. Anytime i buy a used bike i drain the oil right away cause u never know what might be in there...I recommend Castrol Syntec Actevo 10-40 wt. motorcyle oil..buy 4 qts...Put bike level on level ground and after you have drained oil and spun on a new filter...put in 2 qts...then check dipsticks (crisscroos marks on bottom of dipstick should be covered in oil when oil is full) slowly top off checking dipstick frequently so as not to overfill...proper dipstick check is to unscrew stick, wipe it off and reinsert without screwing it in, when oil is to top of crisscross you are full...My friends 2002 F4 has a sight glass NOT a dipstick so incase that's what you have watch oil level in sight glass (should be 1/2 to 3/4 full) Drainplug is under engine and is 17 mm...Good Luck to you friend....Tim

May 14, 2009 | 1998 Honda CBR 600 F(3)W

1 Answer

My bike is leaking oil and gas i know basics in mechanics, i´ve actually ordered the pieces for the gas leaking. I know i can change a gasket, i wanted to know the torque needed to close it back again in...


8 Footpounds of pressure to close it at again
Also could be a simple gasket leak and once fixed might not occur again after you replace gasket you will know if you solved it or not soon enough

Apr 07, 2009 | 2006 Husqvarna SM 610

1 Answer

Hi there, i own an '03 husqvarna sm 450 r, want to change the engine oil but dont know much i will need, i dont want to run short any assistance will be great Thanks, Dylan


Hi Dylan
Oddly, only the transmission oil volume is mentioned in the owners manual, and it appears that the engine and the transmission share the same oil, and require the same 10-60w oil, so I am assuming that is the as listed in the manual  holds 1.41litres (1.48 USquarts or 48 ounces),  You can download the manual by right clicking on   on this  here. and "save file as"   When yo changing the oil, don't forget to clean the filters when changing the oil. Page 100 has details in the manual. Details on the fill level are also in the manual. Hope this has helped. A FixYa rating  is a great reward for looking into this for you. Cheers!
regards robotek

Jan 04, 2009 | 2003 Husqvarna SM 450 R

3 Answers

Change hydrostatic transmission oil


we have tractors and, yes any of those drain bolts will work (for best results do both) then after its drained, put the drain bolts back in and top up the level

Oct 27, 2008 | Husqvarna Garden

Not finding what you are looking for?
2000 Husqvarna WR 360 Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

venugopal durairajan

Level 3 Expert

464 Answers

choprboz5

Level 2 Expert

196 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...