On my 09 cobalt im not getting any primary fuel pump activity and when i turn the key to start starter does not enguage all relays clicking inside and under hood normaly

SOURCE: 1997 Chevrolet Silverado Fuel System

Hello Johnholley
I am wondering do you hear the fuel pump when you just turn the key into the on run position not crank just in run and listen and see if you hear the fuel pump run for a second, If you don't hear it you will want to check for power at the fuel tank, and have some one cycle the key while your under the truck with a test light. Hopefully you have power and you hear the fuel pump run. Now if you do hear the fuel pump running then the next thing you will want to check is for spark, It could be the ignition module or pickup coil. check out those thing and I am sure you will be able to figure out whats going on. If you don't get back to me and we can try a few other methods. I sure hope that helps you out johnholley. and thanks for using Fix Ya Bear001

SOURCE: starting problem, starter doesn't enguage. good starter, battery, celinoid, ignition lock, flex plate.

Have you chk. the starter switch on the steering colume under dash? Or is starter drive kicking in but not engaging teeth in flexplate? If its not engaging teeth on flexplate starter needs to be shimmed, or if its missing the teeth altogether on flexplate or bearly catching the teeth, top of starter nose wear it bolts up needs to be filed down to engage the teeth on flexplate.

SOURCE: 2000 S10 4.3L

At the fuel pump relay you should have 1 full time hot wire. 1 hot wire when you turn on the switch. 1 ground, and the other wire goes to the pump. Test the ground to be sure it is good. If so then jump a hot to the one that goes to the pump and see if it runs.If it does then you have a bad relay or ECM. You can swap the relay with another of the same # from tour fuse box to test it.There is also a ground on top of the frame near the filler neck, check it too. Good Luck

Dar

• 2007 Answers
• Posted on Jul 20, 2009

SOURCE: how can i fix a clogged fuel pump on a 2001 chevy

Have you changed the fuel filter? Did it die while driving, or just wouldn't start? Don't use starting fluid on a gas engine! It will cause a lot more problems than it solves. Ether, starting fluid is made for diesel engines... not gas, not ever. If it won't start, it isn't lacking ether. It's lacking gas, air or spark.

SOURCE: i was having problems with

I have worked on quite a few chevys and can tell you what I've found to work with this type of problem. When you replaced the starter, did you tug on the fusable links that connect to the solenoid to see if one of them was burned and loosing power? There are two or three short pieces of fusable link attached to wires that power the fuse block and other electrical circuits at the solenoid / battery cable connection that will stretch when you pull on them if they are bad. If they are, then you won't have power for the fuel pump, relays and other circuits to make the truck start.
If one is bad, cut the wire behind the link connection and put a **** splice and piece of wire on it with a ring terminal,and connect it to the solenoid. Turn on the ignition and listen for the fuel pump to buzz. The fuel pump is controled by the ECM and makes the pump turn on for 3 seconds to prime the system with fuel before starting the engine. One of the wires on the solenoid with a fusable link does this. If this works, your done.
If the truck won't crank when you try to start it, check the "S" terminal for power with a test light while someone turns the key. The "S" terminal on the solenoid comes from the ignition switch, to the neutral/backup / clutch switch to the starter. You'll have to check every point in between these for power to locate the problem. One bad connection or part will keep the starter from getting power to the "S" terminal. You can use a screw driver to test if the starter is working by touching the two terminals together.
While your under the truck, look at all the wires in the harness for any chafing or rubing, I once found a wire that rubbed through and was causing the problem.
Hope this helps, Craig