Question about Suzuki RM 125 Motorcycles

1 Answer

How much of a job is it to remove the front forks on a 97 RM 125? can they be removed singularly? Anybody got a diagram or procedure to do this??

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Suzuki Master
  • 3,433 Answers

Loosen clamps on triple tree , disconnect lines and remove front wheel, Slide fors downward.. No need to pull them unless replacing or repairing.

Posted on Jun 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a 2016 SX 125. The front suspension has never been right. My rider says it shakes in the air over big jumps. It appears to go away the longer you ride the bike. What could this be?


possible un- even fork fluid in each fork leg. I had those same symptoms on a RM-125, it took myself a while to figure out what it was.

Oct 02, 2016 | 2016 KTM SX 125

1 Answer

How do i change fork seal of kmx 125 a12


Well put on engine stand remove front wheel then mark yokes and fork alignment with marker pen undo retaining clamps on yokes if your forks are upside down ones then undo top cover s then there should be a bolt that holds the inner leg to the fork sleeve once u have removed fork leg remove inner leg from sleeve then you will be able to see the retaining clip inside the sleeve remove this then using a large flat screwdriver get under rubber seal and prize out they are not always easy once done replace with new seal reassemble refill FORK OIL !!! THEN reassemble forks to bike job done

Nov 27, 2014 | Cell Phones

1 Answer

I need to take the forks off omy 1998 rm 125 how do i do that


on top yoke,remove large nuts,bottom yoke,release pinch bolts and legs should slide out

Jul 03, 2010 | 2003 Suzuki RM 125

2 Answers

My 2003 rm 125 transmission slips out of gear.


im having the same problem with my 2003 rm 125, tombones49 is wright about the shift forks.

May 27, 2010 | 2003 Suzuki RM 125

1 Answer

Rm suzuki 125 front forks oil capicety


Do you not have the service or repair manual? Go to Haynes or Google it there will be an answer somewhere just be persistant to look for it... Good luck

Mar 14, 2010 | 2003 Suzuki RM 125

1 Answer

Front forks will not push down at all,how do u adjust softness? and rear is so soft that it bottoms out on jumps,how do u ajust?


wrench or hand turn rear mono shock. Extend the shock for more resistance. Are the front forks air or gas? If they are not pushing down then the rebound is problem bottomed out , air valve on top of forks

Feb 14, 2010 | 2003 Suzuki RM 125

1 Answer

My 2000 suzuki rm 125 does not shift into 4 and 5


The bike has a bent shift fork (or two). The engine needs to come out of the frame then gets torn down in order to replace the forks. Sorry.

Nov 14, 2009 | 2003 Suzuki RM 125

1 Answer

How to seperate upper and lower fork legs - like 4357's ?


Remove upper caps, oil and springs. Slide the upper tubes down to the fork foot, remove a red plastic ring with 3 slits clamped around the chrome tube. Now u can slide the tubes apart.

May 30, 2009 | 2001 KTM EXC 125

1 Answer

Front fork oil seal replacement


General intructions for most bikes:

Remove front wheel. Loosen fork tube clamps at top and bottom of triple clamps. Slide fork tubes out and remove. Access to seals is from top of tube. Remove cover and unscrew cap. Shop manual for specific bike is $24-$30. Will show detailed instructions.

Good luck;
Techjoel

May 14, 2009 | 2001 kawasaki KDX 125

1 Answer

Change oil to Honda nsr 125 front suspension?


A /REMOVE CLIPON HANDLE BARS FROM THE BIKE BY UNDOING ALLEN BOLTS AND SLIDE UPWARS AND OFF
B/JACK BIKE UP SO FRONT WHEEL IS OFF THE GROUND
C/UNDO SLOWLY AND CAREFULLY THE TWO BIG CAPS TOP OF THE SUSPENSION TUBES/
THIS CAREFULLY AS THEY ARE UNDER PRESSURE FROM SPRINGS
C/SLIDE OUT THE SPRINGS ITS BEST TO DO ONE SIDE AT A TIME SO YOU DONT GET THE SPRINGS MIXED UP ALSO REMEMBER WICH WAY UP THEY WERE TOP IS NARROW SPACED
D/ REMOVE FRONT WHEEL
E/ UNDO FORK HOLDING BOLTS AND SLIDE OUT THE SUSPENSION
F/GET A BUCKET AND TURN UPSIDE DOWN SLIDE THE TUBE IN AND OUT TO REMOVE OLD OIL
G/ REFIT TUBES THE GROOVE AT THE TOP OF THE FORK TUBE IS LINED WITH THE TOP OF THE YOKES
TIGHTEN UP ALL BOLTS REPLACE SPRINGS AND FILL FORKS WITH 280ML OF OIL EACH SIDE FINALY REPLACE CAPS AND TIGHTEN DOWN CAREFULLY REFIT CLIPON HANDLEBARS RE FIT WHEEL JOB DONE

Feb 04, 2009 | 2001 Honda NSR 125 R

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...