Question about 1999 kawasaki EL 125 Eliminator

1 Answer

Kawasaki kx 125 rear axel

I was taking the axel out and once i got it out i pulled out the wheel and three washers fell out i need to know where one of them goes i know where two goes but not sure about the other.. is it an extra for one side or what??

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Its not extra it goes on the side of the axle where it meets with the frame

Posted on Jun 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the rear axel


Press the caliper against the rotor while holding the rotor from inside not to bend it.
Unbolt the rear axle's bolt and pull it out.Move the wheel a bit to the front to take off the chain and then remove it.

Feb 06, 2012 | 2005 kawasaki KLX 125

1 Answer

I need to know how to remove lutch from kawasaki 65


1- Remove nuts, clutch spring plate and springs 2 Feed a rolled-up rag between both primary reduction gears to prevent the clutch from turning, then remove the clutch hub nut. 3- Remove clutch hub, pressure plate, steel plates and friction plates. 4- Remove clutch housing. 5- Slide clutch bushing and thrust water from shaft. Take care to note how thrust washer is installed.

Sep 24, 2011 | 2003 kawasaki KX 125

1 Answer

I have a 2004 Kawasaki kx 125 and I finnaly put it back together but I'm having carbarator problems ...I know its out of adujestment and I wanted to know the factory settings for the top pin and the...


Hey Fata.... PLEASE take the carb(or the whole bike) to a QUALIFIED PROFESSIONAL... it will save you time and effort..carb work is NOT for amateurs..there is A LOT more to tuning/cleaning/setting a carb than a screw or two..

Jul 16, 2017 | 2004 kawasaki KX 125

1 Answer

I have an 18" rear


Perhaps you mean brake disc not sprocket..
no you will have problems mounting the brakes

Feb 06, 2011 | kawasaki KX 125 Motorcycles

1 Answer

Need gas-oil ratio on 2004 kawasaki kx 125 2 stroke bike


32:1--40:1 any less than 40:1 And you take risk of damaging engine(crank and top end),Any more than 32:1 and it will smoke real bad and foul spark plugs alot.....

Aug 01, 2010 | 2004 kawasaki KX 125

1 Answer

2001 zx-6r ninja kawasaki


Hi you first take the callipers off then loosen the left 2 allenkeys on front of the fork now you loosen axel with a 17mm allenkey on the side now pull out axell and other side

May 06, 2010 | 2001 kawasaki ZX-6R Ninja

1 Answer

How do you take off the front tire (flat) of a klx 125 kawasaki? Does the brake assembly need to be removed as well?


Some guys leave the brake disk on, some remove the four bolts and leave the disc in the caliper.
Just unbolt the wheel and remove the axle. A “very helpful” rating for this answer? Thanks!

8b59054.gif

Jun 27, 2009 | 2003 kawasaki KX 125

1 Answer

My 1986 kx 125 clutch does not engage worked prior


possible the cable is needing to be adjusted make sure it is pulling on the pivot

Apr 15, 2009 | 2003 kawasaki KX 125

2 Answers

Need to replace wheels on sons power wheels kawasaki brute force fisher price car. i have the wheels but have no idea how to remove old ones and put new ones on. thanks


I just replaced the wheels on the red Fisher Price Kawasaki Brute Force. First use a screw driver to pop off the grey middle nut cover. Then pull of the locking nut with black cap that is under the grey cover you just removed.

Once that is removed the wheel comes right off. There are 4 phillips screws holding the hubs together. Unscrew those and the hubs separate into to pieces (one on each side of the wheel).
Simply place the hubs into the replacement wheels and screw back together. Slide the new wheel on (make sure the washer is still on the rear side of axel).

My replacement wheels actually came with the black replacement locking nuts taped to them. Hammer the replacement locking back on the alex, pop the grey hub cover back on and you are done.

If you are missing the locking nuts, take one of the originals you removed with you to the hardware store and you should have no problem getting them. - MTRAGE

Mar 24, 2009 | Fisher Price Power Wheels Kawasaki KFX...

1 Answer

Removal of front wheel


Simply undo the axle nut and slide out the axle bolt. You might need to take out the split pin if your bike has one.

Nov 13, 2008 | 2003 kawasaki KX 125

Not finding what you are looking for?
1999 kawasaki EL 125 Eliminator Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...