Question about 2008 Suzuki B-king

Open Question

2007 Kig Quad. Digital display flashes Error on all gauges.

If battery dies for too long, all gauges will flash error. The bike will run but can't see fuel, speed, Odometer, ect....

How do I reset without going to shop? The fixed it once and charged me one hour labor.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
Git-R-Dun
  • 6 Answers

SOURCE: Bike runs until the battery dies

Rectifier and/or stator, could be the problem. Check the amperage out put with an amp meter at idle and at 3000 RPM to determine. Troubleshoot all electrical terminals, disconnect, clean, and apply a small amount of Di Electric grease to contacts.
Corrosion causes a lot of problems and is common on bikes after a few years. The main ground wire from the battery to where it connects to the frame is important also. I have found this heavily corroded on a lot of bikes over 10 years old.
Good luck, hope this helps.

Posted on Mar 16, 2009

Ad
  • 125 Answers

SOURCE: bike was sitting for about a year without

Go to the fuel system for your problem. The injectors or filter or valve, something is clogged

Posted on Jun 06, 2009

artsagas
  • 2 Answers

SOURCE: I have a 2001 Suzuki SV650.

The same thing happened to me (2002 sv650) and it turned out to be the voltage regulator. Check it.

Posted on Jul 29, 2009

  • 201 Answers

SOURCE: bike runs but when i try to start it the battery is dead

Do a voltage test at the battery to see how it is charging, it sounds like it is not... You should charge at 14.5 volts. Start the bike with the voltmeter connected and see what it does for voltage drop and see how it recovers after it is started. If it doesn't come up in voltage possible regulator rectifier or worse case bad stator.

Posted on Sep 10, 2009

Testimonial: "cheers mate will try, but has a brand new suzuki rectorfier on and new battery"

SOURCE: Bike dies after running for awhile.

TRY A NEW COIL

Posted on Mar 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What trouble code 23 is on a 2007 sportster 883. think thats the code, turn signals blink left 2 times right 3 times


For a 2007, that's not an error code.
Seems as if your disabler is activating.
The key fob for the security system needs a clear signal to the module to disarm the bike. That's why the flashers turn on. If the fob is at the bike, the security module has lost it's memory, the battery needs replacing, or the antenna for the key fob reception is not connected. You also need to squeeze the clutch lever to allow the engine to engage also...new safety feature i think for 07.

To actually get to the diagnosis mode (to read error codes):

1- Turn motorcycle ignition switch to OFF & Run/Stop switch to RUN.
Push odometer reset button in & hold.
Turn ignition switch to Ignition and release odometer reset button. Background lighting will illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word "diag" should then appear.
Push the odometer reset button once and you will see the selection menu "PSSPt" with the first P flashing.
Turn motorcycle ignition switch to OFF & Run/Stop switch to RUN.
2- Push odometer reset button in & hold.
3- Turn ignition switch to Ignition and release odometer reset button. Background lighting will illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word "diag" should then appear.
4 - Push the odometer reset button once and you will see the selection menu "PSSPt" with the first P flashing.
5 - Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.)
P = ECM/ICM (Electronic Control Module [EFI] / Ignition Control Module [Carburetor])
S = TSM/TSSM (Turn Signal/ Turn Signal Security Module)
SP = speedometer
T = tachometer
6 - To get the DTC in an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC's the code will be displayed or the word "none" will appear if there are no DTC's. Push the odometer reset button again to view additional codes if they exist.
7 - Record the codes.
8 - If DTC's are not to be cleared, Press and release the odometer reset button. Part number of module will be displayed. NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until 'clear' comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC's again by repeating steps 1 to 9. If the code is current it will reappear.
9 - Press and release the odometer reset button to continue to the next module.
10 - Turn Ignition switch to OFF.
On models not equipped with a tachometer "No Rsp" will appear when the tachometer identifier is selected.
"No Rsp" will also appear if the run/off switch is in the off position when doing this procedure.


The actual error codes will appear (format) as "P0374", for example.

Sep 23, 2014 | 2007 Harley Davidson XL 883 Sportster

1 Answer

Busy flash picture and 3484 code


When showing busy, most of the time the camera detected an error, but can't find out what is causing the error.
Try the normal "reset" method as follows:
Like a cold boot for a computer, the camera can be "rebooted"
follow the following steps:
Switch of the camera and remove the battery.
Remove the memory card and the lens. (if possible)
Recharge the battery. Wait till the indicator on the charger indicates the battery is fully charged.
Check all contacts, if they are clean and shiny. Contacts (from battery and memory card, only to be cleaned with a dry cloth or cotton swab(s).
Reinsert the battery, reinsert the memory card and re-attach the lens.
Then switch on the camera.
If this does not help, contact a certified Canon repair centre.

Nov 29, 2013 | Canon EOS 400D / Rebel XTi Digital Camera

1 Answer

2007 Mitsubishi Outlander XLS


Sounds like your alternator stopped working....

Jul 20, 2017 | 2007 Mitsubishi Outlander XLS

1 Answer

2007 Kawasaki zx14 temp gauge flashing hot to cold and will not start and the bike is not hot


on the 2007 that flashes hot and cold and wront start the cdi ecm unit is bad that is what runs all that

May 27, 2012 | 2006 kawasaki ZX-14

1 Answer

E25


hello,


All error codes start with the letter "E". An error code of E11 will have the five indicator lights flash once and the Start indicator light flash once.


Some models of Frigidaire washers come with a digital readout display that informs the operator of the unit's function and any errors.

Error codes indicate that a problem has occurred and should be addressed. Different models of Frigidaire washers may vary in their fault displays.

Some washer models use flashing lights at the unit's start, door lock, wash, rinse, final spin and control indicators to display error codes.



If the five indica

tor lights flash more than nine times, this signals a letter in the error code. The letter "A" stands for 10 flashes, "B" for 11, "C" for 12, "D" for 13, "E" for 14 and "F" for 15 flashes. An error code of EB2 will have the five indicator lights flash or blink 11 times, and the Start indicator light blink twice

hope this help?

thanks.

Oct 23, 2010 | Dishwashers

1 Answer

96 cbr f3. removed gauges now bike will not run right.


its probably put the bike in limp mode which limits the bikes performance while being diagnosed for problems.they cant be read now because you have removed the readout from the system. the meter in these bikes are an integral part of the entire elec. system. when you reinstall the meter, it will probably flash a "code" to show the problem it encountered. unhook the battery for about 5 min. then rehook and start bike. after warmup, it should run ok if all systems are goes.

Oct 24, 2009 | 1996 Honda CBR 600 F(3)T

1 Answer

99 Saturn SC1 ''Service engine soon'' light is on.


Did you get the code that triggered the SEL? If you know that, it will be easier to diagnose your problem. You can do it without a tool on the old saturns. Just need a paperclip. :

Use a paper clip to jumper Terminal A and B of the ALDL *Assembly Line Diagnostic Link* which is above your left knee.
Terminal A is an interal ground and is the top right terminal in the connector. Terminal B is directly adjacent and to the left of Terminal A.

Turn the ignition to ON.

All codes are 2 digits between 11 and 99. Codes are displayed on the SES light by flashing the light with short and long pauses to distinguish digits of one code from digits of another. The short pause is used between digits of the same code, long pauses are between codes. Also, each code is flashed three times before going to the next code.

For example, the sequence of code 12 will be: flash, pause, flash-flash, long pause, then repeat 2 times. If Code 12 is not displayed, the self-diagnostic pogram i snot functioning properly.

If only Code 12 is displayed, no system malfunctions have been stored.

Any existing system fault codes are displayed in order from low to high, except for Code 11.

On vehicles with an automatic transaxle and on which exist stored transaxle codes, Code 11 will be displayed last, then the SHIFT TO D2 light will begin flashing transaxle codes of flags.

When all engine codes have been displayed, Code 12 will flash again.

Diagnostic Codes
11. Transaxle Codes present
12. Diagnostic System Check
13. Oxygen sensor, circuit open or not ready
14. CTS circuit, out of range high
15. CTS circuit, out of range low
17. PCM fault, pullup resistor
19. 6x signal fault, no 6x signal between reference pulses
21. TPS circuit, out of range high
22. TPS circuit, out of range low
23. ATS circuit, out range low
24. VSS circuit, no signal
25. ATS circuit, out or range high
26. Quad Driver output fault
32. EGR system fault
33. MAP sensor circuit, out of range high
34. MAP sensor circuit, out of range low
35. IAC valve, rpm out of range
41A EST circuit open
41B EST circuit shorted
42A Bypass circuit grounded
42B Bypass circuit open
42C Bypass circuit shorted
41. EST bypass, open or shorted
42. EST bypass, open or shorted
43. ECS (knock sensor) circuit open or shorted
44. Oxygen sensor indicates system lean
45. Oxygen sensor indicates system rich
46. Power steering pressure switch circuit, open
49. Idle rpm out of limit high (vacuum leak)
51. PCM memory error
55. A/D converter error in PCM
81. ABS message fault (1993 vehicles with TCS)
82 PCM internal communication fault


Diagnostic Flags
27. Quick quad driver output fault (1993 only)
48. Reference imput intermittent or noisy
52. Battery voltage out of range
53. ESC knock present
54. Five volt reference ground
58. Battery voltage unstable
61. 6x signal fault
63. Option check sum error
67. Handwheel sensor circuit fault
71. Cooling system temperature high
72. Coolinng system temeprature low
73. CTS sensor unstable
74. CTS/transaxle temperatuer sensor ratio error
76. ATS sensor unstable
83. Low coolant (1993 only)

Feb 24, 2009 | 1993 Saturn SC1

1 Answer

I/O device error in flash player


Allow unit to run dead.recharge battery.turn on and push reset(smallpaper clip in reset hole).turn off and back on .should now work.if notformat and download new soft ware athttp://support.creative.com/kb/ShowArticle.aspx?sid=8451.RICHARDM69

Oct 20, 2008 | Creative Labs Zen Neeon MP3 Player

Not finding what you are looking for?
2008 Suzuki B-king Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4736 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...