Question about 2000 KTM EXC 200

1 Answer

My crank shaft is nacked at the end wear the fred is some one hit with a hammer so i need anthoer one

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,567 Answers

You will spend $300 on a new crank plus the $700 cost of installing it. Would you like to spend $1000 or $125 on the repair? Just go to Sears an purchase a metric Tap and Die set. Now you have a tool that will repair the messed up threads on the crank and will also repair threads on nuts and threaded holes. Just be sure the set that you buy has a large enough die for the crank. You could also just buy the single die and the die holder for even less cost. Go to this site if Sears doesn't have what you need. http://www.hermanscentral.com/department/tap-die-sets-10748.cfm?gclid=CJKg4J3apZsCFQazsgodLhD-CQ

A “very helpful” rating for this answer? Thanks! < < And it doesn’t cost anything extra!
my crank shaft is nacked at the end wear the fred - e9244b2.gif

Posted on Jun 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How do I remove the crank arms


You need a tool like this
Bike Bicycle Cycle Crank Extractor Remover Puller

Sep 23, 2016 | Cycling

Tip

How to take a tie rod end off without a pickle fork


on your tie rod end loosen nut untill it is almost all the way off <br />then get a heavy hammer and hit the housing around the bolt shaft<br />that will let the tie rod end fall out or release pressure do not hit the bolt shaft<br />only housing around it<br />

on Dec 29, 2010 | Honda Accord Cars & Trucks

1 Answer

Replaced crank shaft ticking noise


There are a lot of steps involved in replacing a crank shaft where a simple mistake can cause problems. The bolts and end caps need to go back in the exact same position and direction facing the front. The crank needs to be stored upright or it can be damaged simply by its own weight while lying down. The bearings need to be the correct size and installed in the proper position lining oil holes up and greased properly. The bolts need to be torqued in the proper sequence and to the correct torque. The Crank then needs to be tapped with a hammer and torqued again.

Sounds like something was missed if your getting a bottom end engine noise now.

Nov 19, 2013 | Cars & Trucks

1 Answer

Harmonic balancer


align the key way and push it on the end of crank shaft install a ballencer installition kit with bearing abd tighten till its flush dont hit with hammer this causes bad ju ju in the thrust bearings in the engine

Sep 04, 2013 | 1999 Jeep Grand Cherokee

1 Answer

Half shaft will not come out of transaxle on 1994 toyota corolla. Used pry bar and slide hammer


It has a steel retaining ring in a groove on the end of the shaft. Wedge a crow bar firmly in the gap between the ****** and the metal part on the end of the shaft. Hit the crow bar with a heavy hammer. You need one quick hard and solid blow and you will pop it right out. Prying doesnt work as well.

Oct 09, 2011 | Cars & Trucks

1 Answer

Can't get the front left cv off, i've undun the main hub nut (centre) broken the metal bands on both ends of the shaft not sure if i need to take off the whole front hub off to get out the Manuel...


You need to detach the ball joint and tie rod end so you can pull the hub away from the car to give you enough room to remove the end of the shaft from the hub.

Pull the cotter pin out of the tie rod end, then loosen the nut. Hit the tie rod end with a hammer and it will pop out. You need to give it a solid hit with the hammer.

There will be some nuts or screws on the bottom of the ball joint. Remove those screws/nuts.
Then pry the ball joint up until it pops loose and then you can pull the hub away from the shaft to remove the axle.

Sep 10, 2011 | 2001 Hyundai Santa Fe

2 Answers

How do i ger the pin out of the crank shaft on a aprilia rs 125 big end bearing gone but can,t move the large pin holding it together


You need to take the crank to a machine shop. They will use a 20 ton hydraulic press to press the pin out of the crank. A new pin gets the hydraulic press to re-assemble the crank.

Jul 11, 2011 | TN'G RS 125 Motorcycles

2 Answers

I hace the center nut off my dodge 1500 but the cv axle will not break free


no you will not shift it if its been used in a wet climate it will be corroded ,what i do with vehicles that come here and have been imported from northern europe is place a block of wood on the end and hit it with a 14lb hammer ,assistant hold block of wood in place ,if that doesnt shift it then i use a small ball pen hammer and assistant holds the ball into the end of the shaft and i take an even bigger swing -never had one yet that has refused this treatment ,and i havent damaged the thread on the end of the shaft for a number of years

Feb 14, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

Hi I am trying to replace the engine and i need to remove the armature from the crank shaft. there is a long bolt that comes out from the shaft of the armature but what then? I have a hunch that I need a...


I am assuming that you have removed the end bell with field winding and the only obstacle is the rotor on the crank of the engine. I am also assuming that you were able to remove the long bolt thru rotor into crank. Now you will need to apply penetrating oil to the shaft of the engine to loosen the rust on the taper. It may take several applications. Place a piece of hardwood against metal to protect the rotor and firmly rap with hammer on both sides. You may need to use pry bar against engine and rotor as you hammer hardwood. Repeat as necessary, some rotors will be very stuck due to rust. Be very carefull with hammer and or prybars not to damage windings. Have patience and let oil work. Good luck.

Nov 15, 2010 | Coleman Powermate Premium Plus 6250W...

1 Answer

Remove the bearing on a 5hp 110 volt 28 gallon oil less compressor


This is very hard to do but not impossible. The problem is the rod journal is pressed on the motor shaft. You have to remove the coils / rear end of the motor and carefully place the rotor in a vise. Use a steel rod and hammer to gently force the crank off the shaft by hitting crank from rotor side thru vent holes of front motor housing. It will not be easy and you could easily damage shaft, crank or rotor. (but what the heck, it does not work anyway) If your are successful and able to replace bearing, press the crank back on using loctite then drill 1/8" hole thru crank into shaft and drive in a roll pin. Good Luck!

Oct 05, 2009 | Campbell Hausfeld Air Tools & Compressors

Not finding what you are looking for?
2000 KTM EXC 200 Logo

Related Topics:

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top KTM Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Brian Anderson

Level 3 Expert

356 Answers

Are you a KTM Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...