Question about 2006 Hero Honda CD Deluxe
HONDA CD 100 2005 @
Posted by Anonymous on
OK, here's a YouTube video describing how to do this. However it's not in English. But the guy does a good job of showing how to find to drain port and should be sufficient for you to figure the rest out.
Posted on Jun 12, 2019
Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Hero Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Hero Genuine Parts Heromotocorp
Posted on Jun 12, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
SOURCE: Oil change
Ideally you should change the oil every 2000 km. Timely change of oil is vital for all 4 stroke engines. As a simple test after 2000 km touch the oil and feel the viscosity you will note the oil is no longer viscous and feels like water. Under extreme heat oil loses its viscosity faster. If you change oil at 2000 km regularly you will observe that your mileage and drive performance improves.
Posted on Nov 10, 2008
SOURCE: bike starting problem
ALWAYS have a fire extinguisher on hand when working on carburetors.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).
Drain the carburetor. There should be a screw on the lower side or bottom of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.
Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine.
Please rate this solution. Thanks!
Posted on Jun 29, 2009
That sounds like a fair price to me concidering the costs involved.
Please mark this as useful (if it has been!!)
Posted on Aug 03, 2009
Always use Hero Honda 4T plus 20W40 Engine oil and after filling this oil, next oil replacement is after 4000kms.
Oil Filling Procedure: Drain the Old oil and tell the technician to remove the clutch case and remove the rotor and clean the clean the rotor, and then while fitting the clutch case need to replace the rotor gasket and clutch gasket.
Fill only 900 ml of Engine oil, and maintain the Engine oil level between minimum level to maximum level
Posted on Oct 19, 2010
SOURCE: hello sir why any one
Grinding the valves will not affect the oil consumption or carbon build-up in the exhaust. Carbon can be from a rich mixture of fuel, but then the carbon will be a light powder that will rub off easily. If the carbon is hard and baked it will be a combination of fuel and oil, and the only ways you can get excessive oil int he exhaust is if the valve stem seals are leaking or if the rings are worn. Worn rings will make the machine smoke all the time but valve stem seals will make it smoke on first start-up of the day and also when you have rev-ed the machine and suddenly closed the throttle.
Posted on Feb 25, 2011
Tips for a great answer:
May 17, 2014 | 2006 Hero Honda CD Dawn
Jan 28, 2013 | 2003 Honda Civic
Sep 25, 2010 | 2002 Honda Cd 125T
May 18, 2010 | 2002 Honda Cd 125T
May 07, 2010 | Homelite Consumer Products 9.0 Amp, 14 In....
Apr 29, 2010 | 2002 Honda Cd 125T
Jul 29, 2008 | 1997 Honda Accord
Sep 19, 2010 | 2006 Hero Honda CD Deluxe
18 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: