Hi i need cdi box for 94 zx7 l1 l2 or l3 - 1990 kawasaki ZXR 750

First you need to remedy failure or any leakage than reset appliance.
Under Reset I mean to delete all alarm stored in memory.

1. Turn off the dishwasher.
2. Press and hold S1 while switching on the dishwasher. Keep
holding the Program button until:
- LED L1 blinks, L2 and L3 is on
- Release S1
3. When L1 is blinking, L2 and L3 is on, press the S1 before L2 and
L3 is turned off.
- LED L2 is blinking, L1 and L3 is turned on.
4. Wait till L1 and L3 is turned off, then press S1
- All used LEDs flash 5 seconds on 1 second off repeatedly.
- If buzzer is equipped, it beeps for 5 seconds
- The alarms saved in the memory are erased
5. Switch off the appliance.

Dado

E.uPh due to the ripple detection of the DC bus. This is typically caused by a missing phase on the input side of the inverter.

Measure your mains voltage L1-L2, L2-L3, L1-L3 and L1-ground, L2-ground, L3-ground to verify that your supply voltage is balanced and withing the rated specifications.

If the applied voltage is good then there is a problem with the input stage or the DC bus and the unit will need to be repaired or replaced.

L1, L2, L3?
If you are doing statistics, Set MODE to 3. Stat.
Choose 1-Var or any regression model. If you press 1-var you will have two lists x and frequency.
For any regression model you have 3 lists x, y, and Freq(uency).
L1, L2, L3, are list names in the TI 83/84 Plus and the Casio graphing calculators.
However I have no idea what getting the charts up mean.
I hope it helps

L1, L2, L3?
If you are doing statistics, Set MODE to 3. Stat.
Choose 1-Var or any regression model. If you press 1-var you will have two lists x and frequency.
For any regression model you have 3 lists x, y, and Freq(uency).
L1, L2, L3, are list names in the TI 83/84 Plus and the Casio graphing calculators.
I hope it helps

You can't manipulate lists like that.

{5,10,15,20,25}[STO>]L1
{5,5,5,5,5}[STO>]L2

These will input your lists properly. I'm not sure what you're trying to do, but if you're just trying to divide every entry in L1 by 5 and store it in L3, you could accomplish that with:

{5,10,15,20,25}[STO>]L1
L1/3[STO>]L3

Also, this page gives a lot of helpful tips on using lists on a TI-83.
http://pages.central.edu/emp/lintont/ti83/html/lists.pdf

Hope this helps!

It looks like it is 3 Phase, thats why you have L1, L2, L3 One for each Phase. Neutral & Earth.

Hi,
If the data in your L3 list contains only positive numbers there is no reason why you should not be able to calculate the log of the list and store that in L2.

1. You open the list editor, [STAT][1:Edit]
   
2. Use arrows to position the cursor on an element of L2.
   
3. Use UpArrow to highlight the L2 heading (at the top of the list) and press ENTER.
   
4. The data entry line will show L2= ..
   
5. Erase anything that may be on the L2 entry line and type in
6. [LOG] [2nd] [3] (L3) to enter the L3 identifier inside the log (
   
7. Close the right parenthesis. Screen shows L2= log(L3)
   
8. Press [ENTER]
9. The L2 list will be populated with the logs of the elements of L3.

Hope it helps

Assuming you already have L1 and L2 stored:

2ND L1 ^ 2 STO> 2ND L3 ENTER
2ND L2 ^ 2 STO> 2ND L4 ENTER

what kind of light switch are you replacing??? assuming house light switch???
one way or two way switch??
I have not come across the type of switch before.
L1, L2 is just label as line 1 and line 2, comm is usually refer to common (ground wire-white).
is the red wire-hot???

Hi clinnane,
Try these>
During game-play press pause and enter the following codes. The Gnome cheat
Must be entered first for these cheats to work

Gnome Cheat:
R2, L1, R1, L2, Left, Circle
Note: If a cheat is not allowed a Gnome will appear on the Sim's property to
Signify this. You can click this Gnome for money.

Unlock All Socials:
L1, R1, Down, X, L3, R3

Unlock Team Photos:
L3, R3, R1, R2

Unlock All Skins:
L1, R2, X, Circle, Up, Down

Fill Motives:
L2, R1, Left, Circle, Up

Unlock All Locations:
R2, R3, L3, L2, R1, L1

Unlock All Objects:
L2, R2, UP, Triangle, L3 Happy gaming :)