Question about 1982 Yamaha XJ 650

1 Answer

Clutch handgrip is super hard to pull - 1982 Yamaha XJ 650

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 78 Answers

Hi remove the clutch cable see if it pull in andout easy if its hard replace cable or oil
cheers jay

Posted on Jun 24, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

New carpet is very thick. Hard to push vacuum. Is there an adjustment to allow more air?

Your vacuum should have and adjustment for the "depth of pile" of the carpet.
If it has no such thing at all, ( a few do not,) one solution is to pull it backwards slowly instead of pushing it.
It should clean forwards as well as backwards for you.
God bless your efforts.

Jan 03, 2017 | Vacuums

1 Answer

I need to replace the brushes. Don't know how the old one's are removed.

The carbonbrushes if they are short and you will replace them there is a long brown wire on one of the 2 brushes thats goes inside the handgrip but be careful there are 2 plastic pieces for the power licht and the carbon brush is on a electronic modul inside the handgrip by a sliding contact 90 degrees beware also on the black damping rings inbetween the machine and handgrip 4 pieces to protect vibrations . if you have open the handgrip i will say that you allways control the bearing at the end of the armature because its a very to small choosen bearing that is oft in bad condition i mean it , if it has its operating hours if the carbon brushes are short.but the handgrip must be opened for remove the brushes.

Oct 27, 2015 | Hammering

2 Answers

Why Honda rancher green light wont come when in netural and wont start2008

check for faulty safety micro switches on the machine
(seat ,brake ,clutch gear position -neutral etc)

May 05, 2015 | Honda 2008 FourTrax Rancher 4X4 ES

1 Answer

Clutch on my sportster grabbing right off handgrip hard to shift pulled clutch cover n little spring over adjusting nut broke could that be the prob

The spring probably just popped off. It just sticks on to the adjustment lock. You may need to tighten the adjustment screw on the clutch. This is done by removing the lock which is behind the spring and turning the screw counter clockwise until resistance is felt, then put the lock back on. Do not tighten it past this point or the clutch may slip. You should have a small amount of play in the cable. Adjust this with the cable adjuster.

Aug 18, 2014 | Motorcycles

1 Answer

2003 Kawasaki KX 250 hard to pull in the clutch lever

Hi, Anonymous and the usual suspects are:
1. Clutch cable bent, kinked, pinched, rusted or needs lubrication.
2. Hydraulic clutch hose collapsed or pinched.
3. Improper clutch adjustment.
4. Clutch plates rusted.
5. Pressure plate or springs to heavy for service.
6. Damaged clutch shell.
7. Damaged, bent, or stuck push rod assembly.
8. Faulty worm gear mechanism.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
very hard clutch pull on 99 kx125
hard clutch pull on 99 kx 250
OEM Parts for Kawasaki
2003 Kawasaki KX250 Owner Manual

Jan 12, 2014 | 2003 kawasaki KX 250

1 Answer

The clutch is super hard to turn. Is this why my machine won't spin?

if the clutch is locked ... or tight... then the drum would be more likely to not STOP turning...
If the clutch were loose then the drum would not engage with the motor...what brand , make model serial number?

Apr 17, 2013 | Washing Machines

1 Answer

Chain break is engauged on piece that stops chain but doing know how to reset it to get it back on saw.

on the top of the saw in front of the handgrip is a plastic hand protector when this guard is pushed forward it locks the chain,when you pull it backwards towards the handgrip it releases the chain.

Jul 06, 2009 | Garden

1 Answer

Very hard to pull in clutch leaver with out straining left hand. Is this just cable adjustment needed? or do I need a new hand?

With out pulling in you clutch I can't tell you if it is a normal pull or not. You can buy an easy pull ball and ramp for your clutch, or start working out your grip with a tennis ball.

Jun 22, 2009 | 2001 Harley Davidson FXDX Dyna Super Glide...

2 Answers

1991 Kawasaki KX 250 super tight clutch

Help is at Hand (Excuse pun),
This problem described strongly relates to a seizing clutch cable or frayed.
If you remove it try and pull/push the inner with your fingers there should be No resistance, you may get away with a good oiling but I would recommend replacement.
Good Luck!
Paul 'W'
Onyer~EDson(:0) {#><
Please remember to politely rate my effort!

Jan 21, 2009 | kawasaki KX 250 Motorcycles

Not finding what you are looking for?
1982 Yamaha XJ 650 Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts


Level 2 Expert

314 Answers


Level 3 Expert

1216 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1165 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides