Question about 2000 Harley Davidson FLSTC Heritage Softail Classic

1 Answer

How to remove headlight housing 2001 FLSTC - 2000 Harley Davidson FLSTC Heritage Softail Classic

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Harley Davidson Master
  • 3,506 Answers


To remove the headlamp housing assembly disconnect the wiring harness and then remove the bolt underneath the housing and ligt the housing off the mount.

To change headlamp bulbs:

2001 FXSTD, FXSTS and FLSTS Models

Remove the trim ring screw and then the trim ring, pull the wiring connector block off from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to
unhook them from the notches in the headlamp assembly, pivot the wire retaining clip away from the bulb, replace the bulb and re-assemble all.
2001 FXST and FXSTB Models
Loosen the trim ring screw and remove the trim ring, pull the wiring connector block off from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to
unhook them from the notches in the headlamp assembly, pivot the wire retaining clip away from the bulb, replace the bulb and re-assemble all.
FLSTC and FLSTF Models
Except for HDI motorcycles which have a Halogen bulb similar to FXST the FLSTC and FLSTF motorcycles have a sealed beam type headlamp. HDI headlamps also contain a position lamp bulb that is found under the headlamp assembly's rubber boot.
Remove the trim ring screw and then the trim ring, being careful not to bend the two tabs that hold the
top of the trim ring in place, pull the wiring connector block off from the bulb prongs, remove the rubber boot from the back of the headlamp assembly, squeeze the wire retaining clip ends to
unhook them from the notches in the headlamp assembly, pivot the wire retaining clip away from the bulb, replace the bulb and re-assemble all.

Posted on Oct 13, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I get to the front headlight to change it


Re: Replace headlight bulb

  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
BMW e46 HID Headlight Replace
get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-0.jpg

get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 22, 2012 | Cars & Trucks

1 Answer

How to change a light on a 2001 chev cavalier


remove upper air intake splash shield.remove the headlight housing retaining bolts and pull the housing assembly out to access the bulbs.rotate bulb holder counterclockwise to remove bulbs.WARNING YOU NEED TO WEAR CLEAN GLOVE TO REPLACE HEADLIGHT BULBS BECAUSE THEY ARE HALOGEN BULBS. IF YOU TOUCH HALOGEN BULBS WITH BARE HANDS. OILS FROM SKIN WILL CAUSE HALOGEN BULBS TO OVERHEAT BLOW OUT SO WEAR CLEAN DRY GLOVES.

Oct 26, 2012 | Cars & Trucks

1 Answer

Replace a headlight bulb


Hi,
When you open the hood opened, looking at the headlight housing, there are two bolts at the top of the housing that has to be removed. For this you need to access and remove the black plastic cover to access both of them. When the bolts are removed, lift from the top and it should pull out. You will need to turn the bulb retaining ring to free the bulb from the housing.By reverse the above said instructions you can put it all back together.
Thank you !!

Jul 05, 2010 | 2001 Pontiac Sunfire

1 Answer

How to remove front headlight lens on a 2001 Passat Sedan


well if you car has the two part headlamp take out the turn signal housing. and slide out the headlamp housing out in the direction to where you remove the turn signal housing. if you have the one piece housings you have to completely remove the front bumper to remove the headlamp housing

Jul 02, 2010 | 2001 Volkswagen Passat

1 Answer

How to replace a Headlight in 2001 S-10


Well not sure if you have the two rods on the top that turn 90Deg and pull out so you can remove the whole headlight housing like the full size trucks.The bulbs just twist out.You may have to squeeze the ring where it meets the rear of the headlight housing,like a child proof cap.Then just unlug the old one and install the new.Just make sure not to touch the glass or make sure you clean it well before installing.Well hope this helps and good luck.

Mar 14, 2010 | 2001 Chevrolet S-10

1 Answer

2001Buick LeSabre parking light


On top of the headlight housing are two large knurled black plastic knobs.Unscrew them counter-clockwise.Now the whole headlight housing may be removed. Set it on the bumper and you'll have easy access to the marker light.

Nov 12, 2009 | 2001 Buick LeSabre

1 Answer

How do you get the headlight housing off? i am changing fender and cant seem to get the headlight housing out


There is a cover with two screws, remove those two screws and you will find two flat bar "clips". Pull up on the bars to release the headlamp assembly.

Oct 24, 2009 | 2001 Ford Ranger Regular Cab

1 Answer

2001 Buick LeSabre. How to remove headlight assembly... Just need to remove and replace the headlight assembly on my 2001 LeSabre Custom. I think it's just a matter of removing a couple of bolts, but would...


the bolts you are looking to remove are located on the top of the light housing. It only takes 2 of them to remove the housing. One is about 6 to 8 inches long, and the other one is much shorter than that. Just unscrew and remove them, and pull the housing straight out.

Jul 19, 2009 | 2001 Buick LeSabre

2 Answers

How do you replace the headlight bulb on a 2001 chrysler lhs.


This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Jan 28, 2009 | 2000 Chrysler LHS

2 Answers

Headlight won't pop up


Assuming the headlight housing is not damaged, the motor or the relay may be at fault. Try switching the breakers (found under the hood- check your owner's manual for the exact location). Also check your fuses. If you can get the headlight to come up by switching the relay breakers, remove the breaker prior to turning off the lights. That might make the light stay up. There should be a small manual operator located behind the light housing that can be used to put up the light.

Jul 07, 2008 | 2001 Pontiac Firebird

Not finding what you are looking for?
2000 Harley Davidson FLSTC Heritage Softail Classic Logo

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...