Question about Motorcycles

1 Answer

2008 Kawasaki kx 100 kick-starter locks up but moves in 1-6 gears with clutch being held but locks up when being push started

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

My buell acted crazy like that found the chain tensioner broke into pieces

Posted on May 18, 2014

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Clutch wont engage after kickstarter shaft installation.

The clutch lever must have been pushed in when i tried to install the push rod the first time so the push rod didn't get pushed in all the way.

moz-screenshot.jpgmoz-screenshot-1.jpgmoz-screenshot-2.jpg
moz-screenshot-3.jpg7d3aefb.jpg

Posted on May 30, 2009

SOURCE: i have 2003 kawasaki kx 125 when you put it in

Hi cbloom,
You will have to probabley adjust the clutch either from the end of the cable at the side cover or from the above at the handle lever.

Good Luck .


Knight. ( Yamaha Seca XJ750A 1981)

Posted on Feb 18, 2009

  • 1 Answer

SOURCE: 2003 Heritage Starter Problems

I have an 03 FLSTC, same issue. Went through four starters before 70k miles. Problem solved when I had both the gear reduction and compression releases installed. Have 40k miles on my fifth starter and no problems.

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My ( 2008 Kawasaki Kx 100 ) kick-starter won't move down.. I tried Push Starting It and It's Seem To Lick The Back Tire... The GearBox Seem The Be Fine it's goes in neutral &' too gears 1-6 ... Also Moves...


Think you have simply frozen your piston from lack of proper fuel and 2 stroke oul mixture. Bike will move in neutral and with the clutch in, just won't kick or bumpstart ! Time for a top end rebuild my friend...good luck !

May 18, 2014 | Motorcycles

1 Answer

What happens when kick starter jams on kx 100 &' bike tires Jam up too ?? But moves when held with clutch PLEASE HELP !! 2008 KX100


Can you kick the engine over freely if it's in neutral? If yes, then it is a clutch issue. If no, then your engine may be locked up/damaged.

May 18, 2014 | Motorcycles

1 Answer

I have a kawasaki kx 450 and i changed my water pump seal and now my kick start is locked up on me whats would be wrong


I take it that the water pump is gear driven from the engine. In that case you have caused a problem in that you have jammed something when you were putting it back together and this is locking the crank from moving.

Apr 01, 2013 | 2006 kawasaki KX 450 F

1 Answer

My bike starts with kick stand down-safety feature malfunctioning / i unplug the kickstand switch connected the end of the plug with a wire so that i have closed circuit and the problem still exists even...


Hi, Nunjazx12 the ignition circuit cut-off system comprising of the side stand switch, clutch switch and neutral switch has the following functions:
a. It prevents starting when the transmission is in gear and the side stand is up, but the clutch lever is not pulled.
b. It prevents starting when the transmission is in gear and the clutch lever is pulled, but the side stand is still down.
c. It cuts the running engine when the transmission is in gear and the side stand is moved down.
Periodically check the operation of the ignition circuit cut-off system according to the following tests.
With the engine turned off:
1. Move the side stand down.
2. Make sure that the engine stop switch is set to "RUN"
3. Turn the key to "ON".
4. Shift the transmission into the neutral position.
5. Push the start switch if the engine does not start the neutral switch may be faulty.
With the engine still running:
6. Move the side stand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the side stand down if the engine does not stall you may have a faulty side stand switch.
After the engine has stalled:
10. Move the side stand up.
11. Keep the clutch lever pulled.
12. Push the start switch if the engine does not start you may have a faulty clutch switch.
This check is most reliable if performed with a warmed-up engine.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Kick stand safety switch
How to bypass the kickstand safety switch 2008 Kawasaki Ninja 250r
Kawasaki NINJA ZX 12R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Apr 30, 2017 | 2003 kawasaki ZX-12R

1 Answer

My kx 125 was going well then lost power and now can not move kick start at all . how do i tell if the engine is siezed


sounds like it seized! if the kick starter wont go down. take the spark plug out, pour some thin oil down the hole, let it soak overnight, then try moving the kick starter again.

May 09, 2010 | 2005 kawasaki KX 125

2 Answers

Bike will not start with kick starter, has no spark KX 250


there is the problem in the clutch plates kindly remove it by the new one otherwise it will leads to the choking of engine

Apr 29, 2010 | 2005 kawasaki KX 250

1 Answer

My 2004 kawasaki kx 125 has a problem with the starter is locked down. HELP


if your talking about the kick starter lever it sounds like your rebound spring broke on the gear. and you will have to remove the cover to get to it to replace it.

Apr 11, 2010 | 2003 kawasaki KX 125

4 Answers

HOW DO I SHIFT A 2003 KX 250


pull your clutch in on the left handlebar push the shifter lever down and let you clutch out slowly while giveing the bike a lil bit of gas. But if you don't know how to ride i wouldn't be jumping on a kx 250

Sep 20, 2009 | 2003 kawasaki KX 250

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77194 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...