Question about 2005 Honda Silverwing 600 ABS

1 Answer

Left turn signal does not work blub is good all thr rest work.

The left front turn signal does not work and the blub is good.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 107 Answers

Follow the wires sounds like one of the wires may have come adrift.

Even though the bulb looks ok double check it by replacing it with a new one - they are only like $2.50.

Posted on May 19, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I drive a 2005 saturn relay. The left front blinker will not work. We have changed the bulb and it still won't work. All the others work


Why is it you don't take it to the repair shop ? Do you know about automotive electrical circuit's an testing ? Viewing a wiring diagram an using a DVOM - digital volt ohm meter to test . You changed the blub ,but testing the circuit for B+ voltage is what you should have done . Not a fuse problem either . the other's work . Checking for DTC'S - diagnostic trouble code's would be a good first step . The BCM - body control module turns it on an off .

Turn Signal Lamps
The STOP/TURN fuse in the instrument panel (I/P) fuse block supplies battery positive voltage to the body control module (BCM) for the turn signal lamps. When the turn switch is placed in the left or right position, ground is applied to the BCM on the left or right turn signal switch signal circuit. The BCM then applies voltage to the appropriate front and rear supply voltage circuits.
Grounds for the various lamps are as follows:
• G100 supplies the right front lamps
• G101 supplies the left front lamps
• G400 supplies the right rear lamps
• G401 supplies the left rear lamps

DTC B3948 Left Front Turn Signal Circuit
When the turn signal switch is placed in the left turn position, the body control module (BCM) cycles positive voltage ON and OFF to the LF turn signal lamp through the left front turn signal lamp supply voltage circuit. The front turn signal lamps illuminate steady for daytime running lamp (DRL) operation.

Your best bet , take it to a qualified repair shop.

May 03, 2018 | Saturn Cars & Trucks

1 Answer

No turn signals no brake lights no speedo lights no horn on a 2000 dyna fxdl


Hi Anonmous, get out your test light and start at the ignition switch and work your way to switch housings and beyound. If you disconnected the battery for any reason you might have a TSM/TSSM issue. For a free wiring diagram please visit the website below:
Harley Davidson Wiring Diagrams and Schematics
Good luck and enjoy the rest of your day.

Feb 03, 2014 | Harley Davidson FXDL Dyna Low Rider...

1 Answer

Left turn signal dont work. blubs front and rear have been replaced.


Having had this problem before with other GM vehicle, I am pretty sure that your problem is the multi functional switch in the steering column.

Sep 16, 2010 | 2004 Pontiac Bonneville

1 Answer

Front passenger side turn signal blub only last about 3 months before going out.what could be the problem


Are you sure you replaced it with the correct bulb?also look at the connector and see if it looks burnt.If it does then replace it and when you replace the bulb add die electric grease to the contacts.This will keep the heat down.Good luck and I hope this helps.

May 10, 2010 | 2004 Cadillac SRX

1 Answer

The left turn signal doesn't work, howerver rest does


check the blubs and you may have to replace the turn signal switch give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local Mercury dealership in the parts department and they be able to print you off the pictures and diagrams you will need wish you the best of luck Michigan Man.

Mar 22, 2010 | 2001 Mercury Sable

1 Answer

Why won't turn signals work in my 91 camry after replacing burnt out blub in left front


You may have burned the fuse. It is located in the fusebox in the engine compartment, behind the battery. Always disconnect the battery negative terminal whenever you are about to work on anything electrical.

Feb 20, 2010 | 1991 Toyota Camry

1 Answer

Left flasher dead, right on works


double check your bulbs again, if still good
check your flasher

G

May 09, 2009 | 2005 Jeep Wrangler

1 Answer

Left turn signal light out how do i replace it


Again which turn signal bulb are you trying to replace on the left side,the front or the rear?

Mar 09, 2009 | 2003 Ford Escape

Not finding what you are looking for?
2005 Honda Silverwing 600 ABS Logo

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4898 Answers

yadayada
yadayada

Level 3 Expert

79851 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...