Question about Harley Davidson FXR Super Glide Motorcycles
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: replace rear brake pads
Remove right saddlebag, pull the two caliper mounting bolts and remove the caliper. Do not open bleeder or disconnect line. You will need to push a large screwdriver between the old pads before removing them in order to push the pucks back into the caliper or the new pads will not spread enough to reinstall. Then pull the two smaller bolts from the caliper and the pads will fall out. The pads are different for inside and outside, so pay attention, and remember, after reinstalling, before riding, be sure to pump brake pedal, and it may take a few stops before brakes stop as effectively as before.
Posted on Nov 10, 2008
SOURCE: air in rear shocks
Depending on your weight and if you carry a passenger as to the air pressure. I normally run about 14 but 24 if riding 2 up.
up to 150 lbs- 0
each addition 25 rider pounds > 150 lbs add 1.0 lbs
each additional passenger pounds > 150 lbs add 1.5 lbs
each additional 10 lbs of laggage add 3.0 lbs
Max Pressure 35 psi
Posted on Nov 30, 2008
first ya need to suspend it in the air using a bike jack loosen chain tension on it unbolt the axel and it should come out from the rear of the bike
Posted on Mar 27, 2009
your oil drain is on the right side pipe side of your bike look under near the rear back part of your frame you will see a plug with a one quarter allen key threaded plug style bolt kinda hidden in bridge plate of frame it is flat in conjuction with line on bike it is in area right behind where your back pipe expands to baffle of pipe where its skinny and then gets bigger its the one closest to you
Posted on Jun 09, 2009
you should not have to remove shocks dont do that to remove wheel loosen the back section of your exhaust the nut that holds it is the only one you need to take off the back section of your exhaust now loosen the tension screws in front of the axle nut on both sides this creates slack on your belt or chain drive take off big nut on axle use tools on both sides at same time to keep axle from spinning take weight off of wheel just enough to allow wheel to be wiggled and slide the axle out you can tapp on axle just not on threads if you have to beat on it place nut on axle loosly and hit only to free it up it should slide out after a few taps the brakes are on a spacer style format on axle rememmeber with spacer goes on which side they are different in size to accomadate wheel spacing to brakes and belt alignment when wheel drops remove drive type belt or chain wheel should roll out of place you may need to lift bike higher with lift or jack to clear fender on roll out ta dah you have your wheel off to put back on reverse this order i change all my own tires have done all types for friends i hope this helped you
Posted on Jun 10, 2009
Tips for a great answer:
Sep 09, 2014 | 1993 Harley Davidson FXR Super Glide
Mar 20, 2014 | 1993 Harley Davidson FXR Super Glide
Aug 01, 2013 | 2003 Harley Davidson FXDWG Dyna Wide Glide
May 17, 2012 | 2003 Harley Davidson FXDWG Dyna Wide Glide
Aug 18, 2010 | 1993 Harley Davidson FXR Super Glide
Nov 09, 2009 | 1993 Harley Davidson FXR Super Glide
55 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: