Question about Motorcycles

1 Answer

I have a 2008 hyosung gt250r. All of a sudden it has started this issue. Where i start the bike in neutral then go to get first gear and the bike just cuts out each time..so ive had to start off in second gear . How do i go about fixing this problem?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 101 Answers

The problem is the side stand cut out switch - it allows you to start the bike to warm it up on the side stand but if you true to ride off with the side stand down the bike will cut out reminding you the stand is down.
If you bike is cutting out when putting it into gear after starting it is definitely the cut out switch - check the side stand there will be a switch around it some where close to were it bolts onto the frame.

Posted on May 17, 2014

  • Lee Connell
    Lee Connell May 17, 2014

    But it doesnt cut out in second? surely if it was the stand it wouldnt let me go in second

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Audioaholic
  • 376 Answers

SOURCE: my 2008 hyosung gt250r doesnt start, all light and

does it crank over?....if so check spark...fuel...etc...try to narrow it down to a actual problem such as carbs clogged, or injector not working, other than wont start, not able to tell much from that.

Posted on Sep 11, 2009

seanpwright
  • 2030 Answers

SOURCE: 2008 hyosung wont start

I am assuming you mean with the starter button.

If thats the case check that you have power to the button, and if so powewr coming out of the button.

If all is good this far, check the starter solenoid and starter for operation.

try taking 12v directly to the starter and see what happens..if it turns then the problem is before the starter.

Posted on Sep 11, 2009

  • 3567 Answers

SOURCE: my hyosung gt250r makes a nocking sound when i

You probably have a broken tooth on first gear.

Posted on Sep 05, 2010

  • 200 Answers

SOURCE: my 2008 hyosung gt250r will

short in wiring or switch causing battery discharge. charge battery to full charge . see if everything works right. ifturn lights
still dont work, un hook switch to turn signals . wait for the next
day and see if your battery has held charge . should read 12v
or 11.5v . if battery stays up switch maybe shorting out. check wiring for chaffing

Posted on Oct 21, 2010

  • 105 Answers

SOURCE: i have a leaking pet

Make shure its not the sending unit under the tank it easy to miss MOPAR KENNY

Posted on May 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 Hyosung Gt250r carb flooding when I try to ride but idles good only on start up what's causing this?


Hi, Chris and the usual suspects are:
1. Dirt or other foreign matter between float valve and its seat.
2. Float valve sticking.
3. Float valve and/or valve seat is worn or damaged.
4. Float misadjusted.
5. Float cracked, leaky or damaged.
6. Excessive "PUMPING" of hand throttle grip.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Why is the engine bogging under acceleration Suzuki FA50 Moped
will gv250 carbys fit gt250r
http://files.hyosungmotorsusa.com/GT125_250_Service_Manual.pdf https://www.alpha-sports.com/Parts/H_GT250R.htm
HYOSUNG GT250 FI Owner Manual

Feb 18, 2017 | 2010 Hyosung GT250R

1 Answer

Hi mate my hyosung gt250r started randomly stalling while I was ridding, thought it was the kickstand cable, yesterday I went to start it started fine but cut off when I put it in gear, Anny ideas why


It does sound like a kickstand sensor issue, as the sensor only works when the bike is in gear. To check, you can bypass the sensor by disconnecting it's cable and then joining the two wires together so there's a permanent electrical connection. If that solves the problem, you need a new kickstand sensor.

May 12, 2015 | Hyosung Motorcycles

1 Answer

Think same problem with my bike the fuel does not flow fr the tank to the hose and to the carburator i got hyosung gt250r its been a month before i start the bike thne sudden ly fuel not flow


Sounds like the gas tank may have some crud in the bottom that is prevent the fuel from flowing through the petcock.. OR the petcock itself is stopped up. Make sure the petcock is not stopped up first.. then make sure the tank is clean. My personal ATV went through this very thing...the TANK and the PETCOCK were stopped up.
You are going to have to remove the gas tank to do this,
BE CAREFUL!!!!

May 12, 2014 | 2008 Hyosung GT250R

1 Answer

08 hyosung gt250r starting issue


Hi, Ron and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a "LOAD" test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
https://www.perthstreetbikes.com/forum/showthread.php?t=140128
Hyosung GT250R not starting
HYOSUNG COMET 125 Service Manual
http://www.alpha-sports.com/hyosung_parts.htm
http://www.hyosung.com.au/downloads/manuals/GT250.pdf

Mar 15, 2017 | 2008 Hyosung GT250R

1 Answer

Hoses on 2008 Hyosung GT250R


-this is probably some kind of overflow for unspent fuel - or oil vapours - one line will lead in - the other is probably a drain or overflow - which usually drops excess fluids on the ground - without a picture its hard to tell

Jan 06, 2013 | 2008 Hyosung GT250R

1 Answer

2011 Hyosung GT250R instruments keep resetting


Hi, Kingsley for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Hyosung GT250R clock repair
HYOSUNG COMET 125 Service Manual
HYOSUNG GT 250 Service Manual
https://www.alpha-sports.com/Parts/H_GT250R.htm
HYOSUNG GT 125 Manual

May 12, 2017 | 2011 Hyosung GT250R

1 Answer

2008 Hyosung GT650S I think my side stand relay is causing my bike not to start. The Stator was replaced recently and the battery seems to be holding a charge fine. Sometimes the bike just won't...


What I would suggest then is to bridge the side stand switch. If the switch stays open circuit, it will never start but if you bridge the wires before the switch then the bike should start and have now solved the problem for the interim or you if it does not start you know you have to look elsewhere.

Please get back if you require anything else or give favorable feedback.

Thank you

Sep 24, 2011 | Hyosung GT 650 S Motorcycles

1 Answer

2008 Hyosung GT250R will not turn over


Hi, Mcle_cool before testing any electrical component in the Starting System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
4. Bank angle sensor needs a reset or is faulty.
5. FOB battery low or dead.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Security alarm needs a reset.
10. Starter relay, solenoid, starter have failed or circuit wiring faulty.
11. Starter armature or field coils have failed.
12. Main fuse or circuit breaker may be blown or faulty.
13. The electric starter is working but starter clutch has failed.
14. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
https://www.perthstreetbikes.com/forum/showthread.php?t=140128
Hyosung GT250R not starting
HYOSUNG COMET 125 Service Manual
https://www.pdf-archive.com/2015/08/16/manual-reparaci-n-gt250ri/manual-reparaci-n-gt250ri.pdf
https://www.alpha-sports.com/Parts/H_GT250R.htm
HYOSUNG GT 125 Manual

May 23, 2017 | 2008 Hyosung GT250R

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...