Question about 2003 Harley Davidson FLHTCUI Electra Glide Ultra Classic

2 Answers

My 2004 Ultra Classic cruise control , when set, will increase speed gradually on it's own, The brakes deactivate the green indicator light to red but does not shut off cruise control and rolloff feature is very tight and hard to roll off

Posted by on

  • mccarpentry9
    mccarpentry9 May 22, 2014

    Seriously ? This is your solution ? Everything on a bike is fix it yourself, that is the pupose of forums such as these .

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 786 Answers

I do not know anything about the cruise control function on these bikes because mine does not have it but if you go to http://harleytechtalk.org you will find an answer. This is the top rated Harley site on the internet with the most knowledgeable from all over the world.

Posted on May 27, 2014

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Take it to Dealer..not a fix it your self...

Posted on May 22, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 143 Answers

SOURCE: 2005 HD Electra Glide Ultra Classic - Cruse

It is telling you to ditch the beast and buy a BMW.

Posted on Jun 19, 2009

  • 12 Answers

SOURCE: I have a 2007 Electra glide Ultra Classic. The cruise will not e

You may need a new ECM module .

Posted on Oct 26, 2009

wd4ity
  • 4565 Answers

SOURCE: 2004 FLHTCUI Electra Glide Ultra Classic: tire pressure for a 2004 ultra classic...

30 psi in the front and 36 in the rear for single rider. Two up riding, raise the rear tire to 40 psi.

Good Luck and Ride Safe
Steve

Posted on Aug 16, 2010

  • 2 Answers

SOURCE: I have a 05 Ultra

Sounds like the front brake assy. on the handle bar was removed without the card board insert installed between the front break lever and the little piston which can damage it and cause the front brake switch not to work right as the piston in the handle assy. won,t slide back and forth when the lever is moved in and out

Posted on Jun 02, 2011

ruthlesswhit
  • 47 Answers

SOURCE: cruise control not working

Take to the dealer or buy a service manual.

Posted on May 15, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to find fuse control for ford five hundred 2004 cruise control


Do you mean 2005 ? Didn't have five hundred in 2004 !
Speed Control The speed control system consists of the following components:
  • speed control switches
  • speed control deactivator switch
  • speed control indicator
  • powertrain control module (PCM)
  • electronically controlled throttle body
  • clockspring
The speed control system is controlled by the powertrain control module (PCM). The speed control system is designed to maintain a selected vehicle speed between 48 and 200 km/h (30 and 124 mph). The speed control system is controlled by the steering wheel mounted switches (ON, OFF, SET+, SET-, CANCEL, and RESUME), and the brake pedal. The steering wheel mounted switches are hardwired to the PCM.
The speed control functions include:
  • turn the speed control system on
  • set and maintain the desired vehicle speed
  • accelerate the vehicle speed
  • decelerate the vehicle speed
  • resume the prior vehicle speed
  • turn off the vehicle speed control system
  • cancel the speed control
  • Smart junction box (SJB) fuse 18 (10A
  • Powertrain Control Module (PCM) Diagnostic Trouble Code (DTC) Index DTC Description Source Action P0579 Cruise Control Multifunction Input A Circuit Range/Performance PCM Go To Pinpoint Test C . P0581 Cruise Control Multifunction Circuit High PCM Go To Pinpoint Test C . P0720 Output Shaft Speed Circuit Fault PCM REFER to Section 307-01A or Section 307-01B . P0721 Output Shaft Speed Circuit Fault PCM REFER to Section 307-01A or Section 307-01B . P1500 Vehicle Speed Error PCM REFER to Section 307-01A or Section 307-01B . P1501 Vehicle Speed Error PCM REFER to Section 307-01A or Section 307-01B . P1572 Brake On/Off Failure PCM Go To Pinpoint Test B . P1703 Brake On/Off Failure PCM Go To Pinpoint Test B . Highly doubt a fuse problem . Take it to a qualified repair shop.

Jul 18, 2017 | Ford Cars & Trucks

1 Answer

Where is the cruise control fuse located?


In the SJB - smart junction box , Under the dash ! There are three fuse's - F2.27 10amp - F2.32 10amp - F2.17 15amp . Is your air bag light lit ?
SECTION 310-03: Speed Control 2004 Taurus/Sable Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 07/02/2003 Speed Control The vehicle speed control system consists of the following components:
  • Brake pedal position (BPP) switch
  • Speed control actuator cable
  • Speed control switches
  • Speed control deactivator switch
  • Speed control indicator
  • Speed control actuator
  • Smart junction box (SJB)
NOTE: The clock spring provides the electrical interface between the steering column wiring and the speed control switches in the steering wheel.
The inputs to the speed control actuator are:
  • Vehicle speed signal
  • Speed control switches
  • Brake pedal position (BPP) switch
  • Deactivator switch
The outputs of the speed control actuator are:
  • Speed control indicator lamp
  • Speed control actuator cable controlling the throttle position

Apr 01, 2016 | 2004 Ford Taurus

1 Answer

Cruise control


Hi Mike, diagnosing cruise control issues is extremley complex and must be done in a precise manner that involves to many steps to resolve through this media of Fixya. There are a couple of things you can check are your throttle cables to tight (no free play) and is your brake light stuck in the on position. If none of these are an issue you need to take a ride or drive over to your local dealers service/parts department, I'm sure they will be happy to take your Harley Davidson for a test ride if necessary and offer professional advice and assistance concerning your issue. Have a nice day.

Jun 13, 2015 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Cruise control stop working light dont show on dash can a fuse be out if so where is it located


There are three fuse's in the smart junction box , do you know where it is ? It's under the dash panel left side ! The fuse's are F2.27- 10amp , F2.32 - 10amp , F2.17 - 15 amp . They power the speed control servo ! Maybe the control switch's on the steering wheel don't work.
A little back ground on the system ! Speed Control The vehicle speed control system consists of the following components:
  • Brake pedal position (BPP) switch
  • Speed control actuator cable
  • Speed control switches
  • Speed control deactivator switch
  • Speed control indicator
  • Speed control actuator
  • Smart junction box (SJB)
  • Principles of Operation
    The speed control system is designed to maintain vehicle a set speed above 48 km/h (30 mph). After the speed control ON switch is pressed, pressing the speed control switch SET/ACCEL will activate the speed control actuator. To increase a set speed, either press and hold for continuous acceleration, or momentarily tap the speed control switch SET/ACCEL for 1.6 km/h (1 mph) acceleration increments. To decrease a set speed, press and hold the speed control switch COAST until the target speed is reached, or momentarily tap the speed control switch COAST for 1.6 km/h (1 mph) deceleration increments. When the speed control system has been disabled by tapping the brake pedal, the speed control switch RESUME can be pressed and the vehicle will return to the original set speed if the vehicle is traveling over 48 km/h (30 mph) and the speed control switch OFF has not been pressed.
    NOTE: The deactivator switch is provided as an additional safety feature. Normally, when the brake pedal is pressed, an electrical signal from the brake lamp circuit to the speed control actuator will deactivate the system. Under increased brake pedal effort, the deactivator switch will open and remove power to the speed control actuator, releasing the throttle independently of the speed control actuator.
    NOTE: The clockspring provides the electrical interface between the steering column wiring and the speed control switches in the steering wheel.
    The inputs to the speed control actuator are:
    • Vehicle speed signal
    • Speed control switches
    • Brake pedal position (BPP) switch
    • Deactivator switch
    The outputs of the speed control actuator are:
    • Speed control indicator lamp
    • Speed control actuator cable controlling the throttle position
    • Inspection and Verification
      NOTE: If any concerns are noted with the speedometer, stoplamps, or horn, address those concerns by referring to the appropriate sections before continuing speed control diagnosis.
      1. Verify the customer concern by operating the speed control system.
      1. NOTE: Any aftermarket modifications, including but not limited to those listed below, may cause the speed control to not operate correctly:
        • Any wiring or lamp modifications affecting the brake lamp operation
        • LED brake lamps
        • Non-factory installed trailer wiring
        • Radios (speed sensitive, auto mute)
        • Remote starters and alarms
        • Lighting and electrical accessory modifications
        Visually inspect for obvious signs of mechanical or electrical damage:
        • Visually inspect the speed control actuator and accelerator controls.
        • Visually inspect the speed control cable without removing it and ensure smooth cable operation. Inspect the speed control cable connection to the throttle body.
        • Visually inspect the accelerator cable without removing it and ensure smooth cable operation. Inspect the accelerator cable connection to the throttle body. Also check for cable interference with the carpet, bulkhead grommet, insulation and instrument panel wiring.
      1. Visually inspect for obvious signs of mechanical and electrical damage.
      2. Visual Inspection Chart Mechanical Electrical
        • Speed control actuator cable
        • Throttle linkage
        • Battery junction box (BJB) fuse(s):
          • 4 (40A)
          • 12 (60A)
        • Smart junction box (SJB) fuses:
          • 14 (15A)
          • 57 (10A)
        • Wiring harness
        • Loose or corroded connections
        • Deactivator switch
        • Brake pedal position (BPP) switch
        • Speed control switches
        • Powertrain control module (PCM)
        • Speed control actuator
        • Bulb

Mar 14, 2015 | 2007 Ford Taurus

1 Answer

Cruise control indication appear but not enabled


There's a recall for the cruise control deactivation switch. This could be your problem. Contact yo

Feb 22, 2014 | 2002 Mercury Mountaineer

1 Answer

CRUISE CONTROL WON'T WORK ON 2005 CHEVY TRAILBLAZER


check cruise control fuse and check the brake lights see if brake light working because the brake light switch will deactivate cruise control when brakes is applied.if brake lights dont work either fuse blowed or switch bad.if all is good have vechicle code scan because cruise control control by PCM and vechicle speed sensor and thottle actuator control motor.

Apr 17, 2013 | 2004 Chevrolet TrailBlazer

1 Answer

My 2011 Sonata cruise control stops working going down steep hills. The set light goes off. I had it set at 50mph but applied brakes when it increased to 70mph. Dealership says they can find nothing...


going down steep hills will all but over ride a cruise control, since the motor is trying to keep the vehicle slowed to what your desired speed that you set , unfortunately this doesn't always work,, as your speed increases, the motor can't keep the speed reduced, when you apply the brakes, the system shuts off, cruise controls were meant to be used pretty much on long flat surfaces with Low inclines ,,

Aug 25, 2011 | Hyundai Motor 2004 Sonata

1 Answer

I have a 05 Ultra classic where once the cruise control is set it deactivates when I hit any kind of bump in the road. After much tinkering I have found that any and I mean any slight movement in the front...


Sounds like the front brake assy. on the handle bar was removed without the card board insert installed between the front break lever and the little piston which can damage it and cause the front brake switch not to work right as the piston in the handle assy. won,t slide back and forth when the lever is moved in and out

May 25, 2011 | 2003 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Cruise control accelerates after setting it


Most likely due to a problem with the PCM (Powertrain Control Module). You can try disconnecting (for about a minute) and reconnecting your battery which may reset this system and fix the problem. If not, you can bring your vehicle into the dealer, they will perform a diagnostics test for about $95 that will determine what the problem is. If it ends up being the PCM, it is covered under warranty for 8 years 80,000 miles.

Hope this helps.

May 12, 2009 | 2004 Jeep Grand Cherokee

2 Answers

How do you set the cruise control on my 2008 Road King Classic, FLHRCI. I bought the bike, no manual... Thank-you


Luckily, I have a 2008 Road King Classic (FLHRC) WITH a manual!

On the left handlebar switch housing there is a lever below the left turn signal button.
It should be flipped to the right for the cruise control to be on, left is off.

On the right switch housing, is a similar lever, below the right turn signal button.

When you're above the minimum speed (I do not know what this is, but 30 MPH is not fast enough for it to engage), push the lever to the right (towards the grip end). This will "SET" the speed.
If you hit the brakes, or accelerate above a certain rate, the cruise will kick off.
To get back to the set speed, when you're above the minimum speed, flip lever to the left to resume.

When the speed is set and engaged, to increase the set speed, flip right lever to the right, to slow, flip to the left.

Apr 13, 2009 | 2008 Harley Davidson FLHX Street Glide

Not finding what you are looking for?
2003 Harley Davidson FLHTCUI Electra Glide Ultra Classic Logo

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...