Question about 2003 Suzuki GZ 125 Marauder
Can the forks fit the later 2011 model?
Maybe- are the diameter of the fork legs the same and are the fork leg measurements the same centre to centre?
Its possible but hard to answer with out the above information.
Posted on May 15, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Tyre Pressure
As always, correct pressure depends on the tyre fitted but if it is running with the standard tyres that it had fitted from new then:
Single rider: Front is 1.75 bar (25 PSI) Rear 2.0 (29 PSI)
Fully loaded (Panniers and or pillion passenger) Front 2.0 bar (29 PSI) Rear 2.25 bar (32 PSI)
These settings from the book for a 2006 model, though I imagine that they apply to all with very little if any variation
Posted on Jan 23, 2009
hi your exhaust is a sealed item,also your bike is a 4 stroke,why would you need to clean the baffles?only reason these would block up is if you are burning oil,if you are then i would think about a top end overhaul
Posted on Mar 25, 2009
If i were you i would not do this mod. You are going to end up with a ugly top triple tree. Rather find a lower set of bars off another bike. They are all the same diameter tubing.
Posted on Jul 07, 2009
Normally no. If the fork seals are leaking when you ratchet the front down on the trailer your seals were bad prior to that. If you are talking about the straps being wrapped around the forks the only thing that they would contact would be the dust covers. The fork seals are actually down inside the fork about 1/4 inch. Have a good day
Posted on Aug 12, 2009
• Place the front fork vertically without spring.
• Compress it fully.
• Pour specified front fork oil up to the top level of the outer
Capacity (each leg): 490 ml (16.6/17.3 US/lmp oz)
99000-99044-L01: SUZUKI FORK OIL L01
or an equivalent fork oil
• Move the inner rod slowly with the special tool ten times and
more until no more bubbles come out from the oil.
09940-52841: Inner rod holder
Refill front fork oil up to the top of the outer tube so that bubbles
are visible while bleeding air.
• Refill specified front fork oil up to the top level of the outer
tube again. Move the outer tube up and down several strokes
until no more bubbles come out from the oil.
• Keep the front fork vertically and wait 5 – 6 minutes.
* Always keep oil level over the cartridge top end, or air may
enter the cartridge during this procedure.
* Take extreme care so as to pump out air completely.
• Hold the front fork vertically and adjust fork oil level with the
When adjusting the fork oil level, compress the outer tube fully
without the fork spring.
Fork oil level: 153 mm (6.02 in)
09943-74111: Front fork oil level gauge
Posted on Dec 20, 2009
Tips for a great answer:
Oct 08, 2017 | 2001 Suzuki GZ 250 Marauder
Mar 23, 2016 | 2005 Suzuki GZ 250 Marauder
Apr 28, 2015 | 2011 Suzuki Boulevard C50T
Jul 21, 2012 | 2003 Suzuki GZ 125 Marauder
May 15, 2011 | 2000 Suzuki GZ 125 Marauder
Aug 12, 2009 | 1997 Suzuki VZ 800 Marauder
Jul 06, 2009 | 2003 Suzuki GZ 125 Marauder
Mar 25, 2009 | 2002 Suzuki GZ 125 Marauder
Mar 15, 2009 | 2003 Suzuki VZ 800 Marauder
Jan 23, 2009 | 2003 Suzuki GZ 125 Marauder
Jun 08, 2014 | 2003 Suzuki GZ 125 Marauder
121 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: