Yamaha r1 1999 need a video how to install a dog bone

Sure, here are the directions to loosen and remove two bolts from a dog bone:

1. Locate the two bolts. The two bolts that hold the dog bone in place are usually located on the bottom of the dog bone. They are typically hex bolts, but they may also be Torx bolts.
2. Get the proper tools. You will need a wrench or socket wrench that fits the bolts on the dog bone. You may also need a breaker bar if the bolts are difficult to loosen.
3. Loosen the bolts. Start by loosening the bolts by hand. Once the bolts are loose, you can use the wrench or socket wrench to remove them completely.
4. Remove the dog bone. Once the bolts are removed, you can remove the dog bone from the vehicle.
5. Install the new dog bone. If you are installing a new dog bone, follow the instructions that came with the new dog bone.
6. Tighten the bolts. Once the new dog bone is in place, tighten the bolts to the specified torque.

Here are some safety tips to keep in mind when loosening and removing two bolts from a dog bone:

• Make sure that the vehicle is in park or neutral and the parking brake is set before you start working.
• Wear safety glasses to protect your eyes from flying debris.
• Use the correct tools for the job. Using the wrong tools can damage the bolts or the dog bone.
• Be careful not to overtighten the bolts. Overtightening the bolts can damage the dog bone or the vehicle.

I hope this helps! Let me know if you have any other questions.

DOG _bone, is extreme slang in this business. where is it.?does what?
CCW ,
RIGHTY TIGHTY LEFTY LOOSEY(SIC)

unless doing axles.
or on some engine cranks that spin backwards not clock wise spin.

CCW means counter clockwise. for RHT, right hand treads


I guess dog bone is steering box, pitman arm, no such think , on Rack&pinion
no !
I guess topic is :
or suspension link arms. no told what it does this BONE./


not told at all where it is.
Under car, front or rear.??
track link rods
TIE rods.
front strut rods
rear?

CCW ALL I guessed at (bones)

83ft/lbs new. day1 in production line,, strut rod, example guessed
make no bones about it, lots of bones on any Camry

Video? You want a video to show you how to replace a dog bone?

Remove the top dog bone & either pull the motor
toward the front or radiator & block it, or go to amazon
& buy the tool that bolts into the dog bone mount & screws
closed, bringing the motor forward

You could make up something if time isn't an issue

Depending on the engine, some have a mount on top of the radiator.
Its called a dog bone because it is a metal strip with a rubber piece in each end, like a bone. One end bolts to the radiator support, the other bolts to a bracket on top of the engine.
If it has one, you set the brake, put the trans in neutral, unbolt one end and pull the engine forward. Some mounts have a secondary hole to put the bolt in to hold the engine forward.
You can look up "motor mounts - struts" at the online auto parts stores for photos.

Quick fix timing TDCproblem 0. Jack up car on passenger's side, block up for safety. 1. Remove tire #17 lug bolts
2. Remove skirt #10 2 bolts
3. Set crank to TDC "0" #17 bolt on crankshaft. 4. Loosen Power steering pump adjuster bolt #14 remove beltoff pulley. 5. Push PS pump back to fire wall far as possible. 6. Remove both bolts lower dog bone #14 bolts. they are a dog to get off.
6b step one withbraker bar get them loose. 6c Get smaller 1/4" socket wrench to fit on it. #14 1/4 to slip on it in a tight place. 6d Removebolts. Put in lower bone bolts in a cup for i.d.
7. Remove upper dog bolts. Put it upper dog bone cup. 8. Take out dog bone. parts 9. Remove bolts holding in upper timing belt cover. put intiming belt cover cup. 10. Remove upper timing belt cover. Yellow 11. unlock tichner #14 push down on tinchner lock it to makeloose belt. remove thespring with needle nose pliers if it makes it eazy. 12 MOVE CAM TO SEE THE HOLE AND THE ROUND HOLE BEHIND IT,NOT THE OTHER MARK.AS THE BOOK SAYS. THE ROUND HOLE IS ABOUT 5DEG BEFORE THESLIT MARK THAT YOU DON'T WANT TO USE. 13 SLIP THE BELT BACK ON CENTER THE TENCHIN ON THE BELT INBOTH DIRECTIONS FROMTHE CAM SHAFT. ONE TOOTH BACK OF FOWARD RECHECK CAM ANDCRANK MARKS. TIGHTEN IT UP TIME. 14 RELEACE TISHINGNER, TIGHTEN BELT PUSH CAM TO THE LEFT. TO GET TIGHT INBOTH DIRECTIONS TEST FOR PLUCK TONE. 15 START UP CHK TIMING WITH LIGHT. 16 BUT POWER STERING PUMP BACK TIGHT. 17 PUT TIMING COVER BACK ON 18 REINSTALL DOG BONE 19 PUT SKRIT BACK ON 20 PUT TIRE BACK ON. TEST IT ON 3 TRIPS.

There is a dog bone mount at each end of the engine. If it is on the bottom of the engine, something is totally out of whack. The bottom mount is under the transmission and does not look like a dog bone. I am assuming you must be writing the about passenger side, where the serpentine belt is. Remove the right front wheel, put the car on jack stand and remove the plastic service panel behind the wheel. The bolt hole where the dog bone bolt goes will be evident, or there will be a broken bolt. If the dog bones have not ever been changed this would be a time to do that and maybe the belt tensioner too. The other one is under the battery tray, both are fairly easy to replace, assuming you do not bust a bolt off.

It's an engine mount. Usually it will be one at top/front engine and one onside /bottom engine. They are easily replaced, just be sure to take the weight off the mounts with a jack.

I'm thinking it has 1 motor mount and 2 dog bones. The mounts usually cost around $30 each and the dog bones $20-25 depending on the material their made of. You can replace these yourself, one at a time. The engine has to be jacked up just enough to take the weight off when you remove the mount. After you have it remove, install you new one/ones and tighten. After removing jack, torque the bolts to spec. Same thing is done with the dog bones. It a type of Motor mount that prevents the engine from leaning weight. These are usually located, one front/top engine area and one on bottom engine area.

Purchase new dog bones for approxinmately $12 ea and replace one at a time. This is a very easy job.