Question about 2006 Kymco People 150

1 Answer

Turn signals not working

I pulled my 06 people 150 apart to paint it and do alittle bondo work. All the connections where self explanatory and only fit with the connections they came out of. Now I've put it back together and none of the turn signals work. From or back. The dash doesn't flash.... Nothing. What did I miss?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • Kymco Master
  • 1,190 Answers

Did you clean off all your earth points on you nicely painted frame ??

Posted on May 15, 2014


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Left turn signal does not flash when either parking or headlights are on, right signal works ok left turn signal lights are on just not blinking when lights are on, they work ok when lights off

This is usually a bad earth problem, check where the harness earth is then try connecting the earth wire to a different part of the car body in case the rust and Bondo (plastic filler) is so prolific that a good connection is not possible. Then clean all the earth connection point on the globes, the harness connection point, & chassis grounds etc

Feb 12, 2016 | 2005 Ford Explorer

1 Answer

99 toyota 4 runner. Ever sence i had it painted cant get left rear turn signal to work. Front signal works fine just rapidly flashes. Cleaned bulb socket real good didnt help. Rt turn signal works fine...

ater painting , I would be suspecting that a ground point has paint under the contact and is nor making a good ground
also check that the wires are properly connected in the harness

Dec 20, 2017 | Cars & Trucks

1 Answer

How do I replace turn signal switch on a 2002audi a4

hi there, it is an easy enough fix with the correct tools. remove steering wheel, the squibb which is the black round disc looking at you when you remove steering. easy pull wire plugs. then you are looking at the turnsignal switch. self explanatory from there. hope this helps you. cannot do the job its the lack of correct tools for it!!!
its not the person that

May 01, 2014 | 2002 Audi A4

1 Answer

My driver side brake lights went out. I replaced the blubs and the running lights work plus the passenger brake lights work. so I am lost

Its your turn signal switch in the steering colum. just pull your steering wheel and then the switch. I didn,t want to pay $80 for a new one, so I fixed it with bondo! That was about a year ago...still working fine.

Feb 17, 2014 | 1993 Buick Regal

1 Answer

Turn signals don't work, hazard lights work

it could be the switch it self you have to take apart side of steering collom or you mite have to pull steering wheel to get to switch

Dec 11, 2013 | 1993 Honda Accord

2 Answers

I got a dent near my boumper on my 2003. Chevy surberbun and I want to fix it my self how do I start with that

First sand it clean ,then fill it with bondo , sand down smooth and even then prime and paint .

Jan 23, 2013 | Cars & Trucks

1 Answer

Need to fix a dent on the back bumper

You can try pulling it out with a dent puller. Or if your good with bondo use the drill and screw sent puller, pull the dent bondo it, sand it and prime it and paint it.

Jan 26, 2011 | 2006 Honda Odyssey

1 Answer

I pulled the bike apart too spray paint it couse i didnt like the colour and i put it bak together and now the handle bars are hard to turn i have tried loosing the bolds on the goose neck but that didnt...

Sounds like you have some spray paint where there should be only metal to metal contact. Try pulling that area that won't turn apart and cleaning the excess paint off, then reassembling again. if that does not work post again with the specifc part that won't turn.

Dec 06, 2010 | Cycling

1 Answer

I have a rusted roof on my ford ranger. Should I fix it with fiberglass or bondo?

IF it's surface rust you should sand down to bare metal, prime then paint. If it's holes and you don't want to weld in new sheet metal patches then go with bondo

Oct 02, 2010 | 1990 Ford Ranger SuperCab

1 Answer

Hole in front bumper of Infiniti I30 2001

Sure. Use bondo. Do you have a paint sprayer?

Most composite bumpers have the paint in the composite, but I dont' know why, at least for a coupe or three years, the bumper wouldn't hold paint sprayed on.

May 05, 2009 | Hyundai Motor 2004 Sonata

Not finding what you are looking for?
2006 Kymco People 150 Logo

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kymco Experts


Level 3 Expert

80339 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4982 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Kymco Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides