Question about 2000 Harley Davidson XL 1200 C Sportster Custom

1 Answer

I need to see a diagram of spacers for rear wheel

Need to see a diagram of spacers and washers for rear wheel

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Harley Davidson Master
  • 3,506 Answers

Sorry I do not go back to 1990 but if you go to a Harley parts person they cna likley print you off such.

Posted on Oct 14, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 314 Answers

SOURCE: rear wheel spacer placement?

Take great care on reassembly ,as the spacers may be of diffrent lenghts which will if put back wrongly will throw the wheel off its true running centre .and cause problems .Allway remember to mark parts or do a drawing when removing and stripping down for repair or servicing ..It saves a great deal of problems .Try and assemble the spacers and look to see if the wheel is in line with the belt drives .

Posted on Mar 14, 2010

  • 109 Answers

SOURCE: what is the sequence of putting spacers on rear

Not much on newer hogs but I'd guess if the spacers aren't the same length when you got the wheel on you'd see that the wheel isn't centered.Try again.Put the end thru the swing arm put on a spacer,push it thru the hub,put on the other spacer,push it thru swing arm put on washers and nut[loosely]and check the alaignment.Like I said I'm not much.

Posted on Mar 21, 2010

Testimonial: "Your suggestion was very helpful. Thanks! "

wd4ity
  • 4565 Answers

SOURCE: i need to know rear wheel spacer placement. also

The wheel not being equally spaced under the fender is typical of all Softail motorcycles. They have an "offset" wheel stance. I don't know exactly why but they are designed this way.

The three spacers you are talking about is actually one spacer and two seal races. The two seal races go into the wheel bearing seals on either side of the wheel. This provides a smooth finish for the wheel bearing seals to ride on. The other "spacer" is a bit larger and goes on the belt side of the wheel and the rear brake caliper bracket acts as the spacer on the other side. Anytime you take the wheels off your bike, always mark and make a drawing of the positions of the spacers.

Good Luck
Steve

Posted on Oct 12, 2010

wd4ity
  • 4565 Answers

SOURCE: I want to see the

Go to this site http://www.bikebandit.com Click OEM parts. Choose H-D and your year and model of your bike. Click on rear wheel. It may not show the the '04 FXDWG but you can try looking a year earlier or later to find what you need.

Good Luck
Steve

Posted on Apr 24, 2011

wd4ity
  • 4565 Answers

SOURCE: need a diagram of which

You failed to list what year and model bike you have. But, you can go to http://www.bikebandit.com and look at their exploded view drawings. This might help.

Good Luck
Steve

Posted on May 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove 2008 rear wheel fatboy


To remove a 2008 Softail rear wheel FIRST block motorcycle underneath the frame so that theweight of the motorcycle is off of the rear wheel, remove saddlebags if equipped, remove the belt guard and the debris deflector from the rear fork, inspect the wheel bearing end play and service the bearings if and as necessary, label the wheel spacers for left or right locationand orientation i.e. fork side or wheel side, remove the rear brake caliper from the caliper mount and support it using an elastic cord or such,For the FXCW/C modelsthe nut retainer will remain in the axle nut and does not need to be removed and if it is removed it must be replaced. For all but FXCW/C remove e-clip, remove the rear axle nut, and for FXCW/C remove the rear axle nut, loosen both axle adjuster screws an equal number of turns to remove tension from drive belt, with a suitable drift or other tool tap the axle towards the right side and remove it, remove the spacers and the caliper mounting bracket, move the wheel forward and slip the belt off of the sprocket, raise the motorcycle to allow enough clearance for removal of the rear wheel and pull the wheel with the belt sprocket from the rear fork.

To install a 2008 Softail rear wheel FIRST apply a light coat of wheel bearing grease to the axle, to the bearing bores and to the bore of the inner sleeve, roll the wheel into place in the rear fork and slide the drive belt over the drive sprocket, position the left bearing spacer between the wheel and the fork, from the right side carefully insert the axle (with its washer for FXCW/C models) through the right rear fork, the short spacer, the rear caliper mounting bracket, the long spacer and into the bearing bore, continue sliding the axle through the wheel hub sleeve, the left side spacer and the left rear of the fork, install the washer, the axle nut, and the retainer, verify correct axle alignment and the check belt deflection, check the wheel bearing end play after tightening the axle nut to the specified torque because excessive end play can adversely affect stability and handling and insufficient end play can cause bearing seizure, tighten the axle nut to 95-105 ft-lbs (128.8-142.5 Nm), install the belt guard and the debris deflector, install the brake caliper and pads, install the saddlebags, if equipped, pump the brake pedal to move the pistons out until they contact both brake pads, verify the piston location against pads, verify the position of the brake pads against the brake disc, rotate the wheel to check for any interference(s) or misalignment(s) and test the brakes for proper operation.

May 12, 2014 | 2004 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Remove rear wheel


Hi Anonymous, the long spacer went on the pulley side. Have nice day.

Oct 23, 2013 | 2002 Harley Davidson XLH Sportster 883...

1 Answer

Hi I need a diagrame of the layout of spacers on xl 1200 custom rear spindle. Wheel was taken off for rechrome and I do not have a manual !!


My 1200c has the long spacer on the right (belt) side, short spacer on the left (brake caliper) side, and the washer and nut on the left side. Mine is a 2012 model.

Sep 24, 2013 | Harley Davidson XL 1200 C Sportster Custom...

1 Answer

Why are the rear wheels locked up on my toddlers schwinn tricycle?


I took the fenders off to give a little more space for the wheels to move. Don't tighten the nut and washer right up against the black plastic spacer on the rim. Schwinn should be sending out locking spacers or nuts to fix the problem, but I don't see that happening.

Sep 23, 2012 | Pacific Cycle s Schwinn Roadster 12"...

1 Answer

We replaced the rear tire and brake on a 2005 yamaha 1100.each time it is reassembled, the tire is really tight to try & turn it. Any suggestions?


Quite common to get the parts in the wrong order. You should bave a shouldered spacer and a flat washer.
so looking from the back of the wheel...on the right side you should have the following..
wheel
shouldered spacer with shoulder into wheel.
brake caliper bracket
flat washer
swingarm.

if the washers are in the wrong order it pulls caliper against rotor causing the drag

Mar 20, 2011 | 2005 Yamaha V Star 1100 Classic

1 Answer

Hello, I have a 99 evo fatboy, with 3/4" axle. I want to make sure I got all the spacers and washers in the correct order when putting back on. Axle goes in on rotor side, with adjuster on first....


Sounds like you've got it together correctly. There is no washer between the brake caliper bracket and the swingarm. You can put the axle in from either direction. We usually put them in from the left side so that we no longer have to remove a muffler to remove the rear wheel. The nut is now on that side. Just make sure the wheel turns smoothly and the brakes work correctly before taking in out on the road. If you hear a chirping noise when you shift gears, your rear belt is too loose.

Good luck
Steve

Dec 17, 2010 | Harley Davidson FLSTF - FLSTFI Fat Boy...

1 Answer

1993 Kawasaki ZX6E rear wheel bearing diagram


Hi, Est2rad1961 nice novella but all you needed was the bold print up top and what you mean your spelling is bad you only made 78 spelling errors no big scare I cleaned it all up for you at no charge, for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Kawasaki, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day
1993 Kawasaki NINJA 600R ZX600 C6 Rear Wheel Chain
OEM Parts for Kawasaki
Kawasaki 1994 Ninja ZX 6R Service Manual
Kawasaki Ninja ZX 6R Owner Manual
http://www.motorcyclespecs.co.za/model/kawasaki/kawasaki_Zx6%2093.htm

Feb 28, 2017 | kawasaki Ninja ZX6 R Motorcycles

1 Answer

What is the sequence of putting spacers on rear


Not much on newer hogs but I'd guess if the spacers aren't the same length when you got the wheel on you'd see that the wheel isn't centered.Try again.Put the end thru the swing arm put on a spacer,push it thru the hub,put on the other spacer,push it thru swing arm put on washers and nut[loosely]and check the alaignment.Like I said I'm not much.

Mar 03, 2010 | 2005 Harley Davidson FXSTB - FXSTBI Night...

Not finding what you are looking for?
2000 Harley Davidson XL 1200 C Sportster Custom Logo

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...