Question about Motorcycles

1 Answer

941400 intruder front expipe throws no heat runs but missing badly

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 409 Answers

If there is no heat then that cylinder isn't firing...check spark plug...if dry, clean carb...if wet, try a new plug and check for spark

Posted on May 10, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will the clutch switch being jumped cause my Suzuki intruder 1400 to run bad ?


Hi, Shanezzy I don't think so unless you have a faulty connection otherwise the usual suspects are:
1. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
2. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Spark plugs in bad condition or partially fouled.
4. Spark plug cables in bad condition and leaking check for spark leakage in the dark
5. Spark plug gap too close or too wide.
6. Faulty ignition coil, module, and or sensor.
7. Loose, dirty, or corroded ignition module connector at crankcase.
8. Faulty CKP or CMP, MAP, ETS, ATS, TPS, O2 sensor.
9. Dirty air filter.
10. Intake air leak.
11. Water, dirt, or rust in the fuel system.
12. Carburetor damaged, contaminated, sticky float, plugged jets.
13. Multiple carburetors out of sync.
14. Fuel filter clogged.
15. Old or contaminated fuel.
16. Fuel tank vent system plugged or carb vent line closed off.
17. Gas cap diaphragm valve faulty.
18. Vacuum line from intake manifold to fuel valve is broken, cracked, pinched, or missing.
19. Carburetor controls misadjusted.
20. Incorrect valve timing.
21. Valve springs floating, weak, or broken.
22. Damaged intake or exhaust valve.
23. Incompatible performance parts.
24. Control module may be in "LIMP" mode
25. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Intruders Alert
Suzuki intruder 1400 Running Issues
Suzuki Intruder VS1400 Service Manual
OEM parts for Suzuki
Suzuki VS1400 Owner Manual

Apr 14, 2017 | Suzuki VS 1400 Intruder Motorcycles

1 Answer

Code p0170


- Intake air leaks
- Faulty front heated oxygen sensor
- Ignition misfiring
- Faulty fuel injectors
- Exhaust gas leaks
- Incorrect fuel pressure
- Lack of fuel
- Faulty Mass Air Flow (MAF) sensor
- Incorrect Positive Crankcase Ventilation (PCV) hose connection

Nov 26, 2013 | Honda Civic Cars & Trucks

1 Answer

The front cylinder runs fine but the rear cylinder pops and backfires, sometimes the rear cylinder will backfire after the engine is turned off, what can i do to fix this.


That could be the spark plugs causing the run on. The rear piston runs hotter because it is heated by the front one, so try a cooler plug.

Mar 06, 2011 | 1996 Suzuki VS 1400 Intruder

2 Answers

My suzuki intruder is missing backfiring on the


Did you sync the two carbs? If not the rear may be getting all the gas from the rear carb and none to the front. Twist throttle engine off and see if front carb cable is pulling the carb open.
Also unscrew the spark plug boot from the front spark plug wire and trim 1/8th inch off the wire and screw the boot back in. The plug wire end may be corroded on that wire.

Feb 05, 2010 | 2004 Suzuki VS 1400 Intruder

2 Answers

98 Jimmy throws out heat but won't switch to all vent options


Your going to have to replace the switch. The switch it self may have gone bad, since it works on a vacuum. It's common for the diaphragm in the switch assembly to go bad, if it's not the switch. Then it's going to be a bad actuator door and will need to be freed up. I have found it to be the switch it self get dirty and the vacuum needed to activate the actuator door is not there.

Good luck and keep me posted. When you turn the switch from defrost to heater, do you hear a air leak??? If you do then it's a good chance that it's the switch it self.

Dec 03, 2009 | 1998 GMC Jimmy

1 Answer

Where are the 02sensors bank 1 and bank 2 located?


on the expipe should one in front of cat converter if u are looking straight down into the motor one is straight down right off the manifold

Oct 02, 2009 | 2001 Hyundai Sonata

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75744 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...