Question about Motorcycles

1 Answer

My jonway 15000 scooter does not want to switch off after I start it up, kill switch not working,what could the problem be?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Contributor
  • 29 Answers

This can only be the switch as it works by cutting the power to the low voltage side of the coil be carful trying the switch because at the moment the contacts in the switch have moved to give you permeant power but they could just as easily move the outer way and the bike will not start

Posted on May 10, 2014

  • 1 more comment 
  • Dean Holmes May 10, 2014

    What would be the neccessary steps I need to take in order to correct the problem and get it functioning properly again? Thank you kindly for your assistance!

  • mgcoco May 11, 2014

    You will need to replace the kill switch on the Handel bar this is a farly simple job as it is a plug and play

  • mgcoco May 11, 2014

    There are 2 or 3 screws on the under side of the switch gear these will release the switch gear from the Handel bar now follow the cables from it until you find the plug this will be the hardest part when you find it unplug it and plug in the replacment

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: Where can I get an electrical schematic for a

check out go scoot .com very large in china made scooter/atv/dirt bikes

Posted on Sep 12, 2009

  • 1 Answer

SOURCE: I have a 150cc jonway scooter. When I open it up

I found that if I run 87 octane gasoline the engine accelerates up to full speed without the skipping and bogging down at any point it is running. It is worth trying. also try putting some "Sta-bil" fuel stabilizer in the gasoline - it has the ability to keep the carbureator cleaner. Not just during the time you are storing it, but rather all the time.

Posted on Jun 03, 2009

pippall
  • 1486 Answers

SOURCE: YY 150 Jonway cranks good but no start. Hits every

Yes the coil seems to be your problem.

Posted on Aug 01, 2009

  • 1 Answer

SOURCE: there is no spark my scooter wont start what's

The problem may be the accumulator (battery). If you don't have a kicker, try changing the battery

Posted on Jul 25, 2010

  • 1 Answer

SOURCE: Wont start. Turns over

had simular problem with my sl50qt-7 - qmb139 engine - was bad fuel pit **** pump at fuel tank - replaced it and filter and that took care of my problem.

Posted on Oct 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do I get an owners manual for a 2012 Jonway 250cc scooter?


Hi Junior, unfortunately, there is nothing out in the cyber world about an owners manual for your scooter. For more information about your question and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
jonway scooter
Service Support China Jonway Group
http://www.scooterunderground.com/knowledge/manuals/documents/SYM_RV250_Service_manual.pdf
Europe Star Gas Scooter 125cc 150cc 151cc 250cc
http://www.thriftyscooters.com/index.php?main_page=owners_manuals
Atlantic 250cc 2011 12 New Model Touring Scooter Fast Shipping these people may have a manual for you

May 18, 2017 | Jonway Motorcycles

1 Answer

Jonway scooter. When i hit the front breaks: nothing. Is there a way to tighten the front breaks through a span bolt just like rear breaks?


Depends on year, model and cc. Depends on whether the disc brakes are hydraulically operated or cable. First thing to do is to check the condition of the pads. Videos and help in the links.

Jonway scooter Google Search

Jonway scooter brakes Google Search

Apr 19, 2017 | Jonway Motorcycles

1 Answer

When I try to start my 2011 yy250t Jonway scooter it makes a click sound by the starter and won't turn the engine over.


Hi, Becky you might need some help with this it should be noted that in order to "PROPERLY" diagnosis any electric starter issue it is "IMPERATIVE" that you begin with a fully charged battery 12.5 volts or better and be able to pass a proper load test, and the usual suspects are:
1. Battery terminals have loose or corroded connections.
2. Battery cables faulty due corroded or broken internal wiring at the cable connector especially the "NEGATIVE" cable which needs to be checked at "BOTH" ends.
3. Battery voltage, 12.5 volts or better,to the main circuit breaker to the ignition switch to the security/ignition fuse to the TSM/TSSM module to the engine stop/run switch to the starter button to the starter relay to the green wire that connects to the starter solenoid has dropped more than 1/2 volt.
4. With a voltmeter connected to the battery, the ignition switch in the on position, the kill switch in the run position, the starter button depressed, starter engagement should not bring voltage below 8-9 volts.
If a lower voltage is produced a proper battery load test should be performed with a load tester to validate battery integrity or battery replacement.
5. Faulty starter relay, check continuity.
6. Faulty starter solenoid, check contact plate and shoes for excessive electrical erosion/etching, refurbish as necessary or invert contact plate and use the virgin backside. Check contact shoes for being loose. Replace solenoid if the negative function is still a final outcome.
7. Faulty starter, bench test starter with a 12-volt battery if negative function check, decontaminate and undercut armature commutator segments as necessary, check segments with an ohmmeter probe each one and the segment next to it for shorts. Have the armature tested with a growler and field coils, and brush plate with an ohm-meter for opens, shorts or grounds. Replace brushes if less than .438" It is generally cheaper to overhaul/refurbish a starter motor than buy a new one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below the service manual at the bottom link is a clone for your scooter. Good luck and have a nice day.
Identify starter solenoid Scooter Doc Forum
Any suggestions on how to troubleshoot scooter that suddenly no longer...
Chinese Scooter Club View topic Jonway YY250T Zscooter
http://www.carlsalter.com/pdfs/Honda_CN250_Service_Manual.pdf

Aug 08, 2016 | Jonway Motorcycles

1 Answer

Why won't my headlights dash lights and TAIL LIGHTS come back on??? I tried the REGULATOR, not the problem it just stopped on its own. It's a 150cc Jonway scooter


Hi, Crystal you may have a blown fuse or faulty lighting coil for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Jonway, despair not, for a mere $10 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Jonway 150 no lights
Lights aren working HELP Scooter Doc Forum
What to troubleshoot when the headlight isn working scooters
Gy6 50cc 150cc Scooter Repair service Manual Download Manuals Technical

Jun 05, 2016 | Jonway Motorcycles

1 Answer

SCOOTER NOT WORKING


IS THERE KICK START TRY THAT REMOTE PROB BATTERY SWITCH PROB BAD CONNECT IF NOT PROB STARTER/WIRE

Jun 13, 2013 | Jonway Motorcycles

4 Answers

Free jonway scooter repair manuals


jonway 150 is hard to start! Once I get it started it runs great. After setting for about 1 hour, it is hard to start!

Sep 05, 2010 | Cycling

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...